Model reference
Frigidaire FPGH3077RF
Range
11 documents36 error codes5 service modes
Available documentation
Service Manual
- Technical Service Manual Gas Range-FPGH3077RF GAS FCFS111 pg
- Frigidaire Professional 36" Induction Range73 pg
- Dual Fuel Range Slide-in Models and Professional Series Owner's Guide44 pg
- Dual Fuel Range Slide-in Models and Professional Series Owners Guide36 pg
- Electric Range Slide-in Models and Professional Series Owner's Guide72 pg
- Convection Range Professional Series Owner's Guide48 pg
- Dual Fuel Range Slide-in Models and Professional Series Owners Guide24 pg
- Dual Fuel Range Slide-in Models and Professional Series Owner's Guide24 pg
- Electric Range Drop-in/Slide-in Models and Professional Series Owner's Guide28 pg
Training
- Frigidaire Professional 36" Dual Fuel Range Service Training65 pg
- Frigidaire Professional 36" Gas Range Service Training70 pg
MyPros+ Max
Diagnose your Frigidaire FPGH3077RF.
- Step-by-step diagnostics from the service manual
- Test values, resistance specs, and wiring references
- Verified part numbers when replacement is needed
Start diagnosing
$29/month · Cancel anytime · Or $9.95 3-day pass
Error codes (36)
CodeMeaning
1RTD Sensor Error8Cooling Fan ErrorBAD PROBEThe temperature probe has not been completely inserted into the wall receptacle…F01Touch Panel FailureF02Touch Panel FailureF03The Oven User Interface Board is Incorrectly Configured.F04Touch Panel FailureF05Touch Panel FailureF1Electronic oven control has detected a fault condition.F10Oven Temperature RunawayF11Stuck KeyF12Keyboard Configuration AlarmF13Data Written to Non-Volatile Memory has Failed VerificationF15Keyboard ErrorF16The Oven User Interface Board Cannot Read the Potentiometers.F17The Oven User Interface Board is Unable to Configure the Touch Panel.F18Oven Relay Board FailureF19The Oven User Interface Board is Unable to Configure the Oven Relay Board.F22Communication Failure between the Oven User Interface Board and the Oven Relay…F23Communication Failure between the Oven User Interface Board and the Glass Touch…F25The Communication between the Oven User Interface and the Oven Relay Board…F27The Communication between the Oven User Interface and the Oven Relay Board…F28The Communication between the Oven User Interface and the Touch Panel Cannot be…F29The Communication between the Oven User Interface and the Touch Panel Cannot be…F3Electronic oven control has detected a fault condition.F30Open Oven Temperature Sensor (RTD)F31Shorted Oven Temperature Probe (RTD)F33Meat Probe Temperature Sensor Shorted or Too Hot.F50A/D Out of RangeF90Motor Door Lock Mechanism FailureView all 36 error codes
F95Motor Door Lock Mechanism FailureF96The Oven Door has been Detected Open during a Self Clean CycleF97Motor Door Lock Invalid StateLOCKEDThe control panel has been locked to prevent accidental operation.PLEASE INSERT PROBEThe temperature probe has been forgotten or not inserted properly when a…SENSOR ERRORDuring a Sensor feature, the door was opened before steam could be detected, or…
Service modes (5)
- Convection Heater Test P5Refer to convection heater test P5 procedure on page 71 (specific button sequence not detailed in…
- Oven temperature calibration adjustment["Push the BAKE button.","Set the temperature to 550°F by pushing and holding the UP ARROW…
- Relay Test ProcedureRefer to relay test procedure outlined on pages 67-68 (specific button sequence not detailed in…
- Silent control panel mode["Push and hold the STOP TIME button for 7 seconds until the control beeps once."]
- Temperature Adjustment / Calibration Mode1. Make sure both Oven Mode and Oven Temperature selectors are in OFF position. 2. Press and hold…
Full entry steps, exit procedures, and test sequences are available in Max.
Related Frigidaire range models
78,000+ service manuals · 160,000+ error codes · 55+ brands
Get Started$29/month · Cancel anytime · Or $9.95 3-day pass