Model reference

GE PHB925SB1SS

Name: GE PHB925SB1SS
Brand: GE

Range

1 document46 error codes3 service modes

Available documentation

Service Manual

Profile 30 in Free Standing Induction Range PHB925SB1SS Technical Service Guide66 pg
Covers this model

MyPros+ Max

Diagnose your GE PHB925SB1SS.

Step-by-step diagnostics from the service manual
Test values, resistance specs, and wiring references
Verified part numbers when replacement is needed

Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

M+

M+ Max·GE Range

bAd LinE on my GE PHB925SB1SS

M+

Terminal block cord miswire detected.

From Service Manual 382317, p.49:

1.Access service mode to confirm the active fault code and read stored error history.

2.Measure door lock assembly resistance across PTC terminals. Expected: ~200 ohms cold.

3.Inspect strike and latch alignment. A misaligned strike prevents the switch stack from closing.

Part WH44X10288

Door lock assembly

Error codes (46)

CodeMeaning

bAd LinETerminal block cord miswire detected F100LED error on Burner Touch Board (when equipped).F20xTemperature inside oven cavity exceeds 600°F with door unlocked.F21xTemperature inside oven cavity exceeds 900°F with door locked.F30xShorted oven sensor (under 950 ohms).F31xOpen oven sensor (over 2950 ohms).F32xTemperature measurement circuit redundancy check within Main Logic Board bad.F33xTemperature measurement circuit redundancy check within Main Logic Board bad.F40xMeat probe or jack shorted.F600LIN comm error within Main Logic Board.F610LIN comm error to slaves such as RPSM.F611LIN comm error to slaves such as RPSM.F612Line power error detected by RPSM.F620LIN comm error to/from RPSM AUX Board (when equipped).F621LIN comm error to/from RPSM AUX Board (when equipped).F622Line power error detected by RPSM.F640No LIN comm between Main Logic Board and Induction Bridge Board (when equipped).F70xCLEAR/OFF touch key error.F710Any other Touch Key error.F720Main Logic Board internal touch key chip signal error.F73060 Hz square wave not getting to Touch Key chip on Main Logic Board.F740Main Logic Board internal touch key chip signal error.F750Main Logic Board internal touch key chip signal error.F760Main Logic Board internal touch key chip signal error.F770Main Logic Board internal touch key chip signal error.F780Main Logic Board internal touch key chip signal error.F790Main Logic Board internal touch key chip signal error.F7A0Main Logic Board internal touch key chip memory error.F7B0Main Logic Board internal touch key chip memory error.F800Main Logic Board memory error.

View all 46 error codes

F810Main Logic Board memory error.F820Main Logic Board EEPROM memory error.F90xDoor Lock Unlock-Home signal became untrue during cooking.F91xDoor Lock Lock-Home signal became untrue during clean.F92xBoth the Lock-Home and Unlock-Home switches are closed simultaneously.FA00Device not found within Induction Cooktop module.FA10Induction cooktop FA30Induction cooktop FA40Induction cooktop FA47Enable signal not getting from Main Logic Board J241 pin 8 to Cooktop Bridge…FA5xInduction cooktop burner sensor too hot (F-code not logged).FA6xInduction cooktop FA7xInduction cooktop generator board temperature sensor open or DC problem.FA8xInduction cooktop FA9xInduction cooktop FAAxInduction cooktop

Service modes (3)

F-Code RetrievalPress TIMER ON, CLOCK, and START simultaneously
Special Features ModeTouch the upper oven BROIL HI/LO and BAKE pads at the same time until the display shows 'SF'
Test Mode1

Full entry steps, exit procedures, and test sequences are available in Max.

Related GE range models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass