Model reference

KitchenAid KDTE104EBS2

Dishwasher

10 documents48 error codes11 service modes

Available documentation

Tech Sheet

Tech Sheet W10904613 RevB68 pg
Covers this model
Tech Sheet12 pg
Covers this model
KDFE104DSS2 Tech Sheet W10751166 Rev C12 pg
Covers this model
Fiche technique W10751168C16 pg
Covers this model

Service Manual

Dimension Guide2 pg
Covers this model

Wiring Diagram

KDTE204ESS4 Wiring Diagram W10921454 RevA2 pg
Covers this model

Service Flash

Technical Service Pointer - W11753104 - Stainless Steel Dishwasher Models False F10E5 Error6 pg
Covers this model

Tech Tip

Instruction Sheet2 pg
Covers this model

Installation Guide

Installation Instructions76 pg
Covers this model

Other

W11438315 DW03G CF LS wo JennAir)3 pg
Covers this model

MyPros+ Max

Diagnose your KitchenAid KDTE104EBS2.

Step-by-step diagnostics from the service manual
Test values, resistance specs, and wiring references
Verified part numbers when replacement is needed

Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

M+

M+ Max·KitchenAid Dishwasher

1-1 on my KitchenAid KDTE104EBS2

M+

Control detected K1 pilot relay stuck

From Tech Sheet W10302763, p.15:

1.Access service mode to confirm the active fault code and read stored error history.

2.Measure control board supply voltage at test points. Expected: 12 VDC and 5 VDC.

3.Inspect all connectors on the main control for corrosion or backed-out pins.

Part WPW10804018

Electronic control board

Error codes (48)

CodeMeaning

1-1Control detected K1 pilot relay stuck closed.1-2Control software issue 10-1Dispenser electrical problem 10-3Drying fan error 2-2No response from User Interface (UI)3-1Thermistor/OWI open 3-2Thermistor/OWI shorted 3-3Thermistor/OWI failed calibration 4-3Wash motor not running 5-1Door switch stuck open 5-2Door switch stuck closed 6-1Inlet water low/no water (mechanical problem)6-2Fill valve electrical problem 6-3Suds/air in pump 6-4Float switch open 7-1No heat 7-2Heater stuck on 8-2Drain motor electrical problem 8-3Drain stuck on 9-1Diverter can't find position 9-2Diverter stuck on 9-3Diverter disc missing F1-E1Control detected K2 pilot relay stuck closed.F1-E2Damaged or corrupted memory or control board; incompatible software components…F10-E1Dispenser electrical problem; loose connection in dispenser circuit and/or open…F10-E3Drying fan error; loose connection in fan circuit and/or open fan motor.F2-E1Control detected stuck key(s) in keypad or keypad connection.F2-E2User interface cannot communicate with main control; loose user interface…F3-E1Open connector or component in temperature sensing circuit; open or faulty…F3-E2Shorted connection or component in temperature sensing circuit; incoming water…

View all 48 error codes

F3-E3OWI failure; failed calibration F4-E3Wash motor not running; loose connection in motor circuit and/or faulty wash…F5-E1Door stuck open; door was not latched within 4 seconds of pressing Start/Resume…F5-E2Door stuck closed; control programmed to not start if it suspects the door…F6-E1Low/no water (mechanical problem); no water to dishwasher, water captured by…F6-E2Fill valve electrical problem; loose connection in fill valve circuit and/or…F6-E3Suds/air in pump; too many suds, bowls/pots capturing wash water, water…F6-E4Float switch open; overfill switch stuck in overfill position and/or dishwasher…F6-E7Disconnected or damaged flowmeter.F6-E8Regen valve electrical problem; loose connection in regen valve circuit and/or…F7-E1No heat; control programmed to disable heater due to detected water heating…F7-E2Heater stuck on; heater drive circuit on the control is faulty.F8-E1Slow drain; obstructed drain hose or path, or drain pump impeller fractured.F8-E2Drain motor electrical problem; loose connection in drain motor circuit and/or…F8-E3Drain motor stuck on; drain motor drive circuit on the control is faulty.F9-E1Diverter can't find position; corroded or loose connection in diverter…F9-E2Diverter stuck on; diverter drive circuit on the control is faulty.F9-E3Control detected diverter disk in sump is missing.

Service modes (11)

Beeper On/Off TogglePress and hold Hi Temp key for 3 seconds (tone sounds).
Clear Customer Error HistoryDuring Service Diagnostics Cycle interval where Hi Temp LED is on (interval 22-20), press the HI…
Clear Error HistoryDuring Service Diagnostics Cycle interval where Hi Temp LED is on (interval 22), press Hi Temp key…
Control LockPress and hold Control Lock key for 5 seconds to turn On/Off.
Customer Cycle Rapid AdvanceAfter starting a customer cycle, press HIGH TEMP
Rapid Advance (Customer Cycle)After starting a customer cycle, press HIGH TEMP
Rapid Advance (Customer Cycles)After starting a customer cycle, press HIGH TEMP
Rapid Advance Mode (Customer Cycles)After starting a customer cycle, press HIGH TEMP
Sales Demo Mode ExitRun Service Diagnostics Cycle to clear Demo mode.
Service Diagnostic CycleWhile in Standby, press any 3 keys in the sequence 1-2-3-1-2-3-1-2-3 with no more than 1 second…
Service Diagnostics CycleWhile in standby mode, press any 3 keys in the sequence 1-2-3-1-2-3-1-2-3 with no more than 1…

Full entry steps, exit procedures, and test sequences are available in Max.

Related KitchenAid dishwasher models

78,000+ service manuals · 160,000+ error codes · 55+ brands

$29/month · Cancel anytime · Or $9.95 3-day pass