Model reference

KitchenAid KDTE104EWH3

Dishwasher

7 documents51 error codes10 service modes

Available documentation

Tech Sheet

Tech Sheet - W10880571 - Rev A (FR)16 pg
Covers this model
KDTE104ESS3 Tech Sheet12 pg
Covers this model
Tech Sheet12 pg
Covers this model

Service Manual

Dimension Guide2 pg
Covers this model

Service Flash

Technical Service Pointer - W11753104 - Stainless Steel Dishwasher Models False F10E5 Error6 pg
Covers this model

Installation Guide

Installation Instructions76 pg
Covers this model

Other

W11438315 DW03G CF LS wo JennAir)3 pg
Covers this model

MyPros+ Max

Diagnose your KitchenAid KDTE104EWH3.

Step-by-step diagnostics from the service manual
Test values, resistance specs, and wiring references
Verified part numbers when replacement is needed

Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

M+

M+ Max·KitchenAid Dishwasher

1-1 on my KitchenAid KDTE104EWH3

M+

Power relay K2 stuck in closed position

From Tech Sheet W10282922, p.14:

1.Access service mode to confirm the active fault code and read stored error history.

2.Measure control board supply voltage at test points. Expected: 12 VDC and 5 VDC.

3.Inspect all connectors on the main control for corrosion or backed-out pins.

Part WPW10804018

Electronic control board

Error codes (51)

CodeMeaning

1-1Power relay K2 stuck in closed position detected by control module.1-2Control module memory or board damaged/deteriorated, or incompatible software…10-1Dispenser electrical problem 10-3Drying fan error 2-1Stuck key detected 2-2No response from user interface 3-1Thermistor/soil sensor open circuit 3-2Thermistor/soil sensor short circuit 3-3Soil sensor (OWI) calibration failure.4-3Wash motor not functioning 5-1Door switch stuck open 5-2Door stuck in closed position 6-1No water/insufficient water level (mechanical problem) in the dishwasher.6-2Fill valve electrical problem 6-3Excessive suds/air in pump detected.6-4Float switch stuck open in overfill position or incorrect dishwasher leveling.6-7Flowmeter disconnected or damaged.6-8Regeneration solenoid valve electrical problem 7-1No heat 7-2Heating element stuck in active mode 8-2Drain electrical problem 8-3Drain circuit constantly energized 9-1Cannot determine diverter valve position 9-2Diverter valve mechanically blocked (shaft/disc).9-3Missing diverter valve disc in tub bottom detected by control module.F1-E1Control detected K2 pilot relay stuck closed.F1-E2Damaged or corrupted memory or control board; incompatible software components…F10-E1Dispenser electrical problem; loose connection in dispenser circuit and/or open…F10-E3Drying fan error; loose connection in fan circuit and/or open fan motor.F2-E1Control detected stuck key(s) in keypad or keypad connection.

View all 51 error codes

F2-E2User interface cannot communicate with main control; loose user interface…F3-E1Open connector or component in temperature sensing circuit; open or faulty…F3-E2Shorted connection or component in temperature sensing circuit; shorted or…F3-E3OWI calibration failure; OWI failure or drain hose check valve not sealing.F4-E3Wash motor not running; loose connection in motor circuit and/or faulty wash…F5-E1Door stuck open; door was not latched within 4 seconds of pressing Start/Resume…F5-E2Door stuck closed; control programmed to not start if it suspects the door…F6-E1Low or no water to dishwasher (mechanical problem).F6-E2Fill valve electrical problem; loose connection in fill valve circuit and/or…F6-E3Suds or air in pump.F6-E4Float switch open; overfill switch stuck in overfill position and/or dishwasher…F6-E7Disconnected or damaged flowmeter.F6-E8Regeneration valve electrical problem; loose connection in regen valve circuit…F7-E1No heat; control programmed to disable heater due to detected water heating…F7-E2Heater stuck on; heater drive circuit on the control.F8-E1Slow drain; obstructed drain hose or path.F8-E2Drain motor electrical problem; loose connection in drain motor circuit and/or…F8-E3Drain motor stuck on; drain motor drive circuit on the control.F9-E1Diverter cannot find position; corroded or loose connection in diverter…F9-E2Diverter stuck on; diverter drive circuit on the control.F9-E3Diverter disk in sump is missing.

Service modes (10)

Beeper On/Off TogglePress and hold Hi Temp key for 3 seconds (tone sounds).
Clear Customer Error HistoryDuring Service Diagnostics Cycle interval where Hi Temp LED is on (interval 22-20), press the HI…
Control LockPress and hold Control Lock key for 5 seconds to turn On/Off.
Customer Program Fast Forward ModeAfter starting a customer program, press HI TEMP
Demonstration Mode DeactivationRun the Service Diagnostic Program to deactivate demonstration (showroom) mode.
Error Code History RetrievalSame as Service Diagnostic Program entry (1-2-3-1-2-3-1-2-3 key sequence)
Rapid Advance (Customer Cycles)After starting a customer cycle, press HIGH TEMP
Rapid Advance Mode (Customer Cycles)After starting a customer cycle, press HIGH TEMP
Service Diagnostic ProgramIn standby mode
Service Diagnostics CycleWhile in standby, press any 3 keys in the sequence 1-2-3-1-2-3-1-2-3 with no more than 1 second…

Full entry steps, exit procedures, and test sequences are available in Max.

Related KitchenAid dishwasher models

78,000+ service manuals · 160,000+ error codes · 55+ brands

$29/month · Cancel anytime · Or $9.95 3-day pass