Model reference

KitchenAid KDTE234GPS1

Dishwasher

3 documents49 error codes5 service modes

Available documentation

Service Manual

jobaid w10573282120 pg
Covers this model
2013 Stainless Steel Tall Tub Dishwasher120 pg
Covers this model

Tech Sheet

Tech Sheet W11427956A16 pg
Covers this model

MyPros+ Max

Diagnose your KitchenAid KDTE234GPS1.

Step-by-step diagnostics from the service manual
Test values, resistance specs, and wiring references
Verified part numbers when replacement is needed

Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

M+

M+ Max·KitchenAid Dishwasher

1-1 on my KitchenAid KDTE234GPS1

M+

Control detected K1 pilot relay stuck

From Tech Sheet W17838594, p.46:

1.Access service mode to confirm the active fault code and read stored error history.

2.Measure control board supply voltage at test points. Expected: 12 VDC and 5 VDC.

3.Inspect all connectors on the main control for corrosion or backed-out pins.

Part WPW10804018

Electronic control board

Error codes (49)

CodeMeaning

1-1Control detected K1 pilot relay stuck closed.1-2Control software issue 10-1Dispenser electrical problem 10-3Drying fan error 2-2No response from User Interface (UI)3-1Thermistor/OWI open circuit 3-2Thermistor/OWI shorted 3-3Failed OWI calibration 4-3Wash motor not running 5-1Door stuck open 5-2Door stuck closed 6-1Inlet water low/no water (mechanical problem)6-2Fill valve electrical problem 6-3Suds/air in pump 6-4Float switch open 7-1No heat 7-2Heater stuck on 8-2Drain motor electrical problem 9-1Diverter can't find position 9-2Diverter stuck on 9-3Diverter disc missing F10E1Other F10E2Vent wax motor electrical problem F10E3Other F1E1Control F1E2Control F2E1Control detected stuck key(s) in keypad or keypad connection.F2E2User interface cannot communicate with main control; loose user interface…F3E1Open connection or component in temperature sensing circuit; open or faulty…F3E2Shorted connection or component in temperature sensing circuit; incoming water…

View all 49 error codes

F3E3OWI calibration failure.F4E4Wash motor failure due to loose connection in wash motor circuit and/or open…F5E1Door was not latched within 3 seconds of pressing Start/Resume, or loose…F5E2Control suspects door switch is stuck closed; control programmed to not start…F6E1Inlet Water F6E2Fill valve electrical problem F6E3Inlet Water F6E4Inlet Water F6E6Cool water F7E1Heating F7E2Heating F8E1Slow drain F8E2Draining F8E3Draining F8E4Drain motor electrical problem F9E1Diverter F9E2Diverter F9E3Diverter F9E4Lower spray arm error

Service modes (5)

Clear Customer Error HistoryDuring Service Diagnostic Cycle Interval 4, press HI TEMP key to clear customer error history.
Rapid Advance ModeAfter starting a cycle, press HI TEMP
Rapid Advance Mode (during normal cycle)Press HI TEMP
Service Diagnostic Cycle["Ensure the appliance is in Standby mode.","Press any 3 keys in the sequence 1-2-3-1-2-3-1-2-3…
Service Diagnostics CycleWhile in Standby mode, press any 3 keys in the sequence 1-2-3-1-2-3-1-2-3 with no more than 1…

Full entry steps, exit procedures, and test sequences are available in Max.

Related KitchenAid dishwasher models

78,000+ service manuals · 160,000+ error codes · 55+ brands

$29/month · Cancel anytime · Or $9.95 3-day pass