Model reference

KitchenAid KDTE304DPA2

Dishwasher

9 documents29 error codes7 service modes

Available documentation

Tech Sheet

Tech Sheet12 pg
Covers this model
KitchenAid KDTE334D Dishwasher Tech Sheet12 pg
Covers this model

Service Manual

Dimension Guide2 pg
Covers this model
Kenmore Elite 2013 Stainless Steel Tall Tub Dishwashers82 pg
Covers this model

Tech Tip

Installation Instructions1 pg
Covers this model
Instruction Sheet2 pg
Covers this model

Installation Guide

Panel Install Instructions12 pg
Covers this model
Installation Instructions76 pg
Covers this model

Other

technicalreferencemanual 2211031382 pg
Covers this model

MyPros+ Max

Diagnose your KitchenAid KDTE304DPA2.

Step-by-step diagnostics from the service manual
Test values, resistance specs, and wiring references
Verified part numbers when replacement is needed

Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

M+

M+ Max·KitchenAid Dishwasher

1-1 on my KitchenAid KDTE304DPA2

M+

Control detected pilot relay K400 stuck

From Tech Sheet W11687704, p.36:

1.Access service mode to confirm the active fault code and read stored error history.

2.Measure control board supply voltage at test points. Expected: 12 VDC and 5 VDC.

3.Inspect all connectors on the main control for corrosion or backed-out pins.

Part WPW10804018

Electronic control board

Error codes (29)

CodeMeaning

1-1Control detected pilot relay K400 stuck closed.1-2Control software issue 10-1Dispenser electrical problem 10-2Vent wax motor electrical problem 10-3Drying fan error 2-1Control detected stuck key(s) in keypad or keypad connection.2-2User Interface cannot communicate with main control 3-1Open connector or component in temperature sensing circuit (open or faulty…3-2Shorted connection or component in temperature sensing circuit, or incoming…3-3OWI (optical soil sensor) failed calibration.3-4OWI failed calibration 4-4Wash motor failure 5-1Door stuck open 5-2Door stuck closed 6-1Low or no water to dishwasher (mechanical problem).6-2Fill valve electrical problem 6-3Suds or air detected in pump.6-4Float switch stuck in overfill (open) position and/or dishwasher not level.6-6Incoming water temperature under 65°F (29°C)7-1No heat 7-2Heater stuck on 8-1Slow drain 8-2Slow drain 8-3Loose connection in Door Switch Circuit and/or door switch contacts stuck open…8-4Drain motor electrical problem 9-1Diverter can't find position 9-2Diverter stuck on 9-3Diverter disk in sump is missing.9-4Lower spray arm error

Service modes (7)

Clear Customer Error History["Enter Service Diagnostics Cycle.","During the appropriate diagnostics interval (interval with Hi…
Rapid Advance (Customer Cycle)After starting a customer cycle, press HIGH TEMP
Rapid Advance Mode (Cycle Operation)["With door open or closed after starting a cycle, press HIGH TEMP
Rapid Advance Mode (during active cycle)After starting a cycle, press HI TEMP
Sales Demo Mode ClearRun Service Diagnostics Cycle to clear demo mode.
Service Diagnostic CycleWith dishwasher in standby, press any 3 keys in the sequence 1-2-3, 1-2-3, 1-2-3 with no more than…
Service Diagnostics Cycle1

Full entry steps, exit procedures, and test sequences are available in Max.

Related KitchenAid dishwasher models

78,000+ service manuals · 160,000+ error codes · 55+ brands

$29/month · Cancel anytime · Or $9.95 3-day pass