mypros+
Model reference

KitchenAid KDTE554CSS0

Dishwasher

5 documents55 error codes6 service modes

Available documentation

Tech Sheet

  • Fiche technique W10617420C16 pg
    Covers this model

Service Manual

  • Kenmore Elite 2013 Stainless Steel Tall Tub Dishwashers82 pg
    Covers this model

Installation Guide

  • Installation Instructions Undercounter Dishwasher56 pg
    Covers this model
  • Instruction Sheet for Heater Element kit2 pg
    Covers this model

Other

  • technicalreferencemanual 2211031382 pg
    Covers this model
MyPros+ Max

Diagnose your KitchenAid KDTE554CSS0.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (55)

CodeMeaning
1-1Control detected K400 pilot relay stuck closed.1-2Damaged or corrupted memory on control board; incompatible software components…10-1Dispenser electrical problem; loose connection in dispenser circuit and/or open…10-2Vent wax motor electrical problem; loose connection in vent circuit and/or open…10-3Drying fan error; loose connection in fan circuit and/or open fan motor; faulty…2-1Control detected stuck key(s) in keypad or keypad connection.2-2User interface cannot communicate with main control; loose user interface…3-1Open connection or component in temperature sensing circuit; open or faulty…3-2Shorted connection or component in temperature sensing circuit; shorted or…3-3OWI failure; failed calibration.4-4Wash motor failure; loose connection in wash motor circuit and/or open wash…5-1Door stuck open; door was not latched within 3 seconds of pressing…5-2Door stuck closed; control programmed to not start if it suspects door switch…6-1Low/no water (mechanical problem); no water to dishwasher, bowls capturing wash…6-2Fill valve electrical problem; loose connection in fill valve circuit and/or…6-3Suds/air in pump; too many suds, bowls capturing wash water, water leaking…6-4Float switch open; overfill switch stuck in open position and/or dishwasher not…6-6Cool water; incoming water temperature under 18°C/65°F.7-1No heat; control programmed to disable heater if it detects a water heating…7-2Heater stuck on; faulty heater drive circuit on the control.8-1Slow drain; obstructed drain hose or path; drain pump impeller fractured or…8-4Drain motor electrical problem; loose connection in drain motor circuit and/or…9-1Diverter can't find position; corroded or loose connection in diverter…9-2Diverter stuck on; faulty diverter drive circuit on the control.9-3Control detected diverter disk in sump is missing.9-4Lower spray arm error; mechanical binding or blocking of spray arm; corroded or…F10E1Detergent dispenser electrical problemF10E2Vent linear motor electrical problemF10E3Drying fan errorF1E1Control module detected power relay K400 stuck in closed (active) position.
View all 55 error codes
F1E2Damaged or deteriorated memory on control module board, or incompatible…F2E1Control module detected one or more stuck keys on keypad or corresponding…F2E2User interface cannot communicate with main control module, or incorrect user…F3E1Open circuit in temperature sensing circuitF3E2Short circuit in temperature sensing circuitF3E3Soil sensor (OWI) calibration failure.F4E4Wash motor inoperativeF5E1Door not latched within 3 seconds after pressing Start/Resume, or defective…F5E2Door switch stuck in closed positionF6E1No water or insufficient water levelF6E10Water reservoir valve stuckF6E2Fill valve electrical problemF6E3Excessive suds or air in pump causing repeated wash periods.F6E4Float switch stuck open (overfill position) and/or dishwasher not level, or…F7E1No heatF7E2Heater element stuck in active modeF8E1Slow drainF8E2Drain pump impeller broken.F8E3Drain motor not operatingF8E4Drain motor electrical problemF8E9Water reservoir valve inoperativeF9E1Diverter valve cannot find its positionF9E2Diverter valve stuck activeF9E3Diverter valve disc missing from tub bottomF9E4Lower wash arm error

Service modes (6)

  • Clear Error HistoryDuring interval 4 of the service diagnostic program (Hi Temp LED displayed), press the Hi Temp…
  • Customer Program Fast Forward ModeAfter starting a customer program, press HI TEMP
  • Rapid Advance Mode (during active cycle)After starting a cycle, press HI TEMP
  • Sales Demo Mode ClearRun Service Diagnostics Cycle to clear demo mode.
  • Service Diagnostic CycleWith dishwasher in standby, press any 3 keys in the sequence 1-2-3, 1-2-3, 1-2-3 with no more than…
  • Service Diagnostic ProgramIn standby mode, press any 3 keys in the sequence 1-2-3-1-2-3-1-2-3, with less than 1 second…

Full entry steps, exit procedures, and test sequences are available in Max.

Related KitchenAid dishwasher models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass