Model reference
Whirlpool WDF530PAYW2
Dishwasher
17 documents30 error codes13 service modes
Available documentation
Tech Sheet
- Tech Sheet - W10350334 - Rev A (FR)2 pg
- Tech Sheet W10350334 Rev A FR wdf530paym32 pg
- Tech Sheet - W10580720 - Rev B12 pg
- Tech Sheet - W103503332 pg
- Whirlpool Dishwasher WDF530PLYW0 Tech Sheet2 pg
Service Manual
- Global Wash System 2011 Undercounter Dishwashers Technical Education98 pg
Service Flash
- Installation Pointer - W10484438 (Gap Between Door and Console)6 pg
- Remove & Install Door Panel/console Ass'y3 pg
- TESTING THE GWS WASH MOTOR - Technical Service Pointer W105089109 pg
- PLASTIC TALL TUB UNDERCOUNTER DISHWASHER Metal Strike Plate and Door Seal Kit3 pg
Tech Tip
- Instruction Sheet2 pg
- quickreferenceinsertsheet-w10164331-reva-sp.pdf1 pg
- Installation Instructions6 pg
Other
- Whirlpool Dishwasher WDT910SAYE0 WDT910SAYH0 WDT910SAYM0 Users Manual W1035035940 pg
- W10460578B9 pg
Installation Guide
- Installation Instructions48 pg
- Instruction Sheet2 pg
MyPros+ Max
Diagnose your Whirlpool WDF530PAYW2.
- Step-by-step diagnostics from the service manual
- Test values, resistance specs, and wiring references
- Verified part numbers when replacement is needed
Start diagnosing
$29/month · Cancel anytime · Or $9.95 3-day pass
Error codes (30)
CodeMeaning
1-1Control detected K2 pilot relay stuck closed.1-2Damaged or corrupted memory on control board or incompatible software…1-3Control detected stuck key(s) in keypad or keypad connection.10-1Dispenser electrical problem10-2Vent wax motor electrical problem.10-3Drying fan error2-1User interface stuck key or short circuit(s) in keypad or in control's input…2-2Shorted key or short circuit(s) in keypad or in control's input lines that read…3-1Open temperature sensing circuit3-2Shorted temperature sensing circuit3-3OWI/thermistor sensor failed calibration.4-3Wash motor not running5-1Door stuck open5-2Door stuck closed6-1Inlet water6-2Inlet water6-3Inlet water6-4Inlet water6-6Inlet water6-7Flowmeter problem6-8Inlet water7-1Heating7-2Heating7-7Flowmeter problem8-1Draining8-2Draining8-3Draining9-1Diverter9-2Diverter stuck on9-3Diverter disk missing from sump.Service modes (13)
- Clear Customer Error HistoryDuring Service Diagnostics Cycle interval 20, press Hi Temp key when Hi Temp LED is on during the…
- Error History ReadingEnter Service Diagnostics Cycle. Error codes are displayed in intervals 24 (Error 1
- Rapid Advance (during Service Diagnostics)Press the Start/Resume key to advance 1 interval at a time during the Service Diagnostics Cycle.
- Rapid Advance ModePress HI TEMP
- Rapid Advance Mode (Customer Cycles)After starting a customer cycle, press HIGH TEMP
- Rapid Advance Mode (Cycle Operation)After starting a cycle, press HI TEMP
- Rapid Advance Mode (during active cycle)Press HI TEMP
- Rapid Advance Mode (during normal cycle)Press HI TEMP
- Rapid Advance Mode (in-cycle)After starting a cycle, press HI TEMP
- Service Diagnostic CycleRefer to Tech Sheet provided with the dishwasher for specific entry sequence
- Service Diagnostics - Error Code ReadingAfter entering Service Diagnostics Cycle
- Service Diagnostics CycleWhile in standby, press any 3 keys in the sequence 1-2-3-1-2-3-1-2-3 with no more than 1 second…
- Service Diagnostics Error History ReadoutAfter entering Service Diagnostics Cycle, errors are displayed in intervals 24 (Error 1
Full entry steps, exit procedures, and test sequences are available in Max.
Related Whirlpool dishwasher models
78,000+ service manuals · 160,000+ error codes · 55+ brands
Get Started$29/month · Cancel anytime · Or $9.95 3-day pass