mypros+
Model reference

Whirlpool WDT710PAHB0

Dishwasher

10 documents71 error codes11 service modes

Available documentation

Tech Sheet

  • Tech Sheet - W11348206 - Rev A_W113482062 pg
    Covers this model
  • Tech Sheet26 pg
    Covers this model
  • Tech Sheet - W11349311 - Rev A26 pg
    Covers this model
  • Tech Sheet12 pg
    Covers this model
  • KDFE104DSS2 Tech Sheet W10751166 Rev C12 pg
    Covers this model
  • Fiche technique W10751168C16 pg
    Covers this model

Service Manual

  • Global Wash System 2011 Undercounter Dishwashers Technical Education98 pg
    Covers this model

Service Flash

  • Service Pointer - W10460581 (Moisture Detected Inside Door Panels)2 pg
    Covers this model
  • PLASTIC TALL TUB UNDERCOUNTER DISHWASHER Metal Strike Plate and Door Seal Kit3 pg
    Covers this model

Installation Guide

  • Installation Instructions Undercounter Dishwasher Plastic Tub76 pg
    Covers this model
MyPros+ Max

Diagnose your Whirlpool WDT710PAHB0.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (71)

CodeMeaning
1-1Control detected K2 pilot relay stuck closed.1-2Damaged or corrupted memory or control board; incompatible software components…10-1Dispenser electrical problem; loose connection in dispenser circuit and/or open…10-3Drying fan error; loose connection in fan circuit and/or open fan motor, or fan…2-1Control detected stuck key(s) in keypad or keypad connection.2-2User interface cannot communicate with main control; loose user interface…3-1Open connector or component in Temperature Sensing circuit; open or faulty…3-2Shorted connection or component in Temperature Sensing circuit; shorted or…3-3OWI calibration failure; OWI failure or drain hose check valve not sealing.4-3Wash motor not running; loose connection in motor circuit and/or faulty wash…5-1Door stuck open; door was not latched within 4 seconds of pressing Start/Resume…5-2Door stuck closed; control programmed to not start if it suspects door switch…6-1Inlet water low/no water (mechanical problem); no water to dishwasher, captured…6-2Fill valve electrical problem; loose connection in fill valve circuit and/or…6-3Suds/air in pump; too many suds, bowls capturing wash water, water leaking, or…6-4Float switch open; overfill switch stuck in overfill position and/or dishwasher…6-7Flowmeter disconnected or damaged.6-8Regen valve electrical problem; loose connection in Regen valve circuit, and/or…7-1No heat; control programmed to disable heater due to detected water heating…7-2Heater stuck on; Heater Drive circuit on the control is shorted.8-1Slow drain; obstructed drain hose or path, or drain pump impeller fractured.8-2Drain motor electrical problem; loose connection in drain motor circuit and/or…8-3Drain stuck on; drain motor drive circuit on the control is shorted.9-1Diverter can't find position; corroded or loose connection in diverter…9-2Diverter stuck on; diverter drive circuit on the control is shorted.9-3Control detected diverter disk in sump is missing.F1-E1Control detected K2 pilot relay stuck closed.F1-E2Damaged or corrupted memory or control board; incompatible software components…F10-E1Dispenser electrical problem; loose connection in dispenser circuit and/or open…F10-E3Drying fan error; loose connection in fan circuit and/or open fan motor.
View all 71 error codes
F10E1OtherF10E3OtherF2-E1Control detected stuck key(s) in keypad or keypad connection.F2-E2User interface cannot communicate with main control; loose user interface…F3-E1Open connector or component in temperature sensing circuit; open or faulty…F3-E2Shorted connection or component in temperature sensing circuit; incoming water…F3-E3OWI failure; failed calibrationF4-E3Wash motor not running; loose connection in motor circuit and/or faulty wash…F4E3Wash MotorF5-E1Door stuck open; door was not latched within 4 seconds of pressing Start/Resume…F5-E2Door stuck closed; control programmed to not start if it suspects the door…F5E1Door SwitchF5E2Door SwitchF6-E1Low/no water (mechanical problem); no water to dishwasher, water captured by…F6-E2Fill valve electrical problem; loose connection in fill valve circuit and/or…F6-E3Suds/air in pump; too many suds, bowls/pots capturing wash water, water…F6-E4Float switch open; overfill switch stuck in overfill position and/or dishwasher…F6-E7Disconnected or damaged flowmeter.F6-E8Regen valve electrical problem; loose connection in regen valve circuit and/or…F6E1Inlet WaterF6E2Inlet WaterF6E3Inlet WaterF6E4Inlet WaterF6E7Inlet WaterF6E8Inlet WaterF7-E1No heat; control programmed to disable heater due to detected water heating…F7-E2Heater stuck on; heater drive circuit on the control is faulty.F7E1HeatingF7E2HeatingF8-E1Slow drain; obstructed drain hose or path, or drain pump impeller fractured.F8-E2Drain motor electrical problem; loose connection in drain motor circuit and/or…F8-E3Drain motor stuck on; drain motor drive circuit on the control is faulty.F8E1DrainingF8E2DrainingF8E3DrainingF9-E1Diverter can't find position; corroded or loose connection in diverter…F9-E2Diverter stuck on; diverter drive circuit on the control is faulty.F9-E3Control detected diverter disk in sump is missing.F9E1DiverterF9E2DiverterF9E3Diverter

Service modes (11)

  • Beeper On/Off TogglePress and hold Hi Temp key for 3 seconds (tone sounds).
  • Clear Customer Error HistoryDuring Service Diagnostics Cycle interval where Hi Temp LED is on (interval 22-20), press the HI…
  • Clear Error HistoryDuring Service Diagnostics Cycle interval where Hi Temp LED is on (interval 22), press Hi Temp key…
  • Control LockPress and hold Control Lock key for 5 seconds to turn On/Off.
  • Customer Cycle Rapid AdvanceAfter starting a customer cycle, press HIGH TEMP
  • Rapid Advance (Customer Cycle)After starting a customer cycle, press HIGH TEMP
  • Rapid Advance (Customer Cycles)After starting a customer cycle, press HIGH TEMP
  • Rapid Advance Mode (Customer Cycles)After starting a customer cycle, press HIGH TEMP
  • Sales Demo Mode ExitRun Service Diagnostics Cycle to clear Demo mode.
  • Service Diagnostic CycleRefer to Tech Sheet provided with the dishwasher for specific entry sequence
  • Service Diagnostics Cycle["With the appliance in standby mode, press any 3 keys in the sequence 1-2-3-1-2-3-1-2-3 with no…

Full entry steps, exit procedures, and test sequences are available in Max.

Related Whirlpool dishwasher models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass