Model reference

Whirlpool WOC95EC0AH03

Name: Whirlpool WOC95EC0AH03
Brand: Whirlpool

Oven

7 documents41 error codes26 service modes

Available documentation

Tech Sheet

Tech Sheet - W10425194 - Rev A (FR)24 pg
Covers this model
Tech Sheet - W10425195 - Rev C32 pg
Covers this model
TechSheet W10796081 RevB56 pg
Covers this model
Tech Sheet56 pg
Covers this model

Tech Tip

Instruction Sheet2 pg
Covers this model
installerlabel-w10643344-reva.pdf2 pg
Covers this model

Installation Guide

Installation Instructions20 pg
Covers this model

MyPros+ Max

Diagnose your Whirlpool WOC95EC0AH03.

Step-by-step diagnostics from the service manual
Test values, resistance specs, and wiring references
Verified part numbers when replacement is needed

Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

M+

M+ Max·Whirlpool Oven

F1 E0 on my Whirlpool WOC95EC0AH03

M+

Internal MRC board error.

From Tech Sheet W10952627, p.39:

1.Access service mode to confirm the active fault code and read stored error history.

2.Measure control board supply voltage at test points. Expected: 12 VDC and 5 VDC.

3.Inspect all connectors on the main control for corrosion or backed-out pins.

Part WPW10804018

Electronic control board

Error codes (41)

CodeMeaning

F1 E0Internal MRC board error.F1 E1Internal MRC board error.F1 E5Microwave oven inverter error.F1 E7Internal error.F1 E9No display F1-E1Internal error in the control module.F1-E7Internal error in the control module.F1-E9Internal error in the control module.F1E0EEPROM Communication Error F1E1Upper RTD Uncalibrated F1E2Lower RTD Uncalibrated F1E5Sensor Usage Out of Range F1E7PCB Thermistor Open or Shorted F1E9WIDE Queue Full F2 E0Keypad disconnected.F2 E1Stuck key on keypad.F2 E2Invalid keypad.F2 E3Cancel key error.F2E0Keypad Disconnected F2E1Stuck Keypad F2E2Cancel or Off Keypad Error F3 E0Main oven temperature sensor open or shorted.F3E0Main Sensor Open or Shorted (Upper)F3E1Main Sensor Open or Shorted (Lower)F4 E1Microwave oven magnetron thermistor open or shorted.F4 E4Microwave oven humidity sensor open or shorted.F4E1Microwave Oven Magnetron Thermistor Open or Shorted F4E4Microwave Oven Humidity Sensor Open or Shorted F5 E0Door and latch switches do not agree.F5 E1Latch not operating.

View all 41 error codes

F5E0Door and Latch Switches Do Not Agree F5E1Latch Not Operating F6 E0Lost communication with microwave.F6 E1Over temperature during cooking.F6 E2Over temperature during cleaning.F6-E1Overheat condition during baking.F6-E2Overheat condition during self-clean cycle.F6E0Lost Communication with Microwave F6E1Over Temp Cook F6E2Over Temp Clean F9E0Miswired

Service modes (26)

Auto Test ModeEnter Diagnostics Mode (CANCEL > CANCEL > START)
auto_testEnter diagnostic mode
Control ResetEnter Diagnostics Mode (CANCEL > CANCEL > START)
control_resetEnter diagnostic mode
diagnosticPress CANCEL > CANCEL > START in sequence.
Diagnostics ModePress CANCEL>CANCEL>START or OFF>OFF>ON within 5 seconds. Use TEMP/TIME '+' or '-' or 'More' or…
Engineering ModeEnter Diagnostics Mode (CANCEL > CANCEL > START)
engineering_modeEnter diagnostic mode
Fault Display Reset - MicrowaveEnter Diagnostics Mode
Fault Display Reset - OvenEnter Diagnostics Mode
fault_display_resetEnter diagnostic mode
Faults ScreenEnter Diagnostics Mode, navigate to 'Faults' using TEMP/TIME '+'/'-' or 'More'/'Less' or number 3/6…
Oven Light TestEnter Diagnostics Mode (CANCEL > CANCEL > START)
Oven Temperature CalibrationPlug in oven
oven_temperature_calibrationPress SETTINGS until 'TEMP CALIB' is displayed, then press START. For double oven
Relay ActivationEnter Diagnostics Mode. Control auto-enters Test Mode. Activate relays individually
Relay Activation (Test Mode)1. Plug in oven or connect power. 2. Enter Diagnostics Mode (CANCEL>CANCEL>START). 3. Control will…
relay_activationEnter diagnostic mode
Semi Automatic Test ModeEnter Diagnostics Mode, then navigate with TEMP/TIME '+'/'-' or 'More'/'Less' or number 3/6 keypads…
Software VersionEnter Diagnostics Mode (CANCEL > CANCEL > START)
software_versionEnter diagnostic mode
Temperature CalibrationPress Settings or Options keypad until 'Temp Calib' is displayed
Test ModeEnter Diagnostics Mode, then navigate with TEMP/TIME '+'/'-' or 'More'/'Less' or number 3/6 keypads…
test_modeEnter diagnostic mode (CANCEL > CANCEL > START)
Usage CodesEnter Diagnostics Mode
usage_codesEnter diagnostic mode

Full entry steps, exit procedures, and test sequences are available in Max.

Related Whirlpool oven models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass