mypros+
Model reference

Whirlpool GGE390LXQ03

Range

4 documents30 error codes15 service modes

Available documentation

Tech Sheet

  • Tech Sheet - W10457101 - Rev A_W1045710116 pg
    Covers this model

Service Manual

  • Troubleshooting Gas and Electric Freestanding Range Electronic Controls70 pg
    Covers this model

Installation Guide

  • Installation Instructions20 pg
    Covers this model
  • Instruction Sheet1 pg
    Covers this model
MyPros+ Max

Diagnose your Whirlpool GGE390LXQ03.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (30)

CodeMeaning
F1Control failure or UL A/D error(s) detected in the control board.F1 E*Control board failure (all F1 sub-codes indicate control fault).F1-E0EEPROM communication error.F1-E1Upper RTD uncalibrated.F1-E2Lower RTD uncalibrated.F1-E5Sensor usage out of range.F1-E7PCB Thermistor/Sensor open or shorted.F1-E9WIDE Queue full.F2Shorted/stuck key detected on the control keypad.F2-E0Keypad disconnected.F2-E1Stuck key.F2-E2Stuck key.F3Oven sensor opened or oven sensor shorted.F3 E0Oven temperature sensor fault (open or shorted)F3 E1Lower oven temperature sensor fault (MRC II double oven models).F3 E2Warming drawer temperature sensor fault.F3-E0Main sensor open or shorted (upper oven).F3-E1Main sensor open or shorted (lower oven).F5 E0Door position switch faultF5 E1Door latch switch/system faultF5 E2Door switch fault.F5-E0Door and latch switches do not agree (Clean mode).F5-E1Door latch not operating (Clean mode).F6 E*Control communication failure.F6-E0Lost communications.F6-E1Over temperature during cook mode (runaway temp).F6-E2Over temperature during clean mode (runaway temp).F6-E3Over temperature in warming drawer (runaway temp).F9House miswiredF9-E0Product is mis-wired.

Service modes (15)

  • Control Reset1
  • Diagnostics ModePress CANCEL > CANCEL > START.
  • Display Test1
  • Faults (Error Code Review)1
  • LCC Diagnostic Mode (LCC90/LCC95/LCC180)["Press CANCEL, CANCEL, START in sequence.","Press TEMP/TIME '+' key to cycle through diagnostic…
  • LCC190 Diagnostic Mode (Self Clean, Convection models)["Press CANCEL, CANCEL, START in sequence.","Press TEMP/TIME or TEMP/HOUR '+' key to cycle through…
  • MRC Diagnostic Mode["Press CANCEL, CANCEL, START in sequence.","Press TEMP/TIME '+' key to cycle through diagnostic…
  • MRC Diagnostic Mode (Fan/True Convection Electric - Oven Light entry)["Press CANCEL, CANCEL, START in sequence.","Press TEMP/TIME '+' key to cycle through diagnostic…
  • MRC II Diagnostic Mode (Number 3 key entry - KitchenAid models)["Press OFF/OFF/START or CANCEL/CANCEL/START in sequence.","Press the number '3' key to cycle…
  • MRC II Diagnostic Mode (TEMP/TIME entry)["Press CANCEL, CANCEL, START in sequence.","Press TEMP/TIME '+' keypad to cycle through diagnostic…
  • Semi Automatic Test1
  • Temperature Calibration Adjustment1
  • Test Mode1
  • Usage1
  • Version1

Full entry steps, exit procedures, and test sequences are available in Max.

Related Whirlpool range models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass