Model reference

Whirlpool IGS365RS1

Range

9 documents34 error codes6 service modes

Available documentation

Tech Sheet

TECH SHEET - 9755996 - Rev A4 pg
Covers this model
techsheet 9755996 reva4 pg
Covers this model

Service Manual

Whirlpool Gas Range Direct Spark Ignition System29 pg
Covers this model
Job Aid - 30″ Freestanding Self-Cleaning Gas Range68 pg
Covers this model
30″ Freestanding Self-Cleaning Gas Range68 pg
Covers this model
Whirlpool Gas Range Direct Spark Ignition System KR-2829 pg
Covers this model

Installation Guide

Installation Instructions16 pg
Covers this model
Instruction Sheet2 pg
Covers this model
Instruction Sheet2 pg
Covers this model

MyPros+ Max

Diagnose your Whirlpool IGS365RS1.

Step-by-step diagnostics from the service manual
Test values, resistance specs, and wiring references
Verified part numbers when replacement is needed

Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

M+

M+ Max·Whirlpool Range

F0 E0 on my Whirlpool IGS365RS1

M+

Factory default - not an error.

From Tech Sheet W14312762, p.14:

1.Access service mode to confirm the active fault code and read stored error history.

2.Measure control board supply voltage at test points. Expected: 12 VDC and 5 VDC.

3.Inspect all connectors on the main control for corrosion or backed-out pins.

Part WPW10804018

Electronic control board

Error codes (34)

CodeMeaning

F0 E0Factory default F1 E0EEPROM communications error.F1 E1EEPROM checksum error.F1 E2UL A/D error(s).F1 E4Model ID error.F1 E6Latch signal mismatch error.F1-E0EEPROM communications error.F1-E1EEPROM checksum failure.F2 E0Shorted key.F2 E1Key tail unplugged.F2 E2UL A/D error(s).F2-E2UL A/D error(s).F3 E0Oven sensor opened F3 E1Oven sensor shorted F3 E2Bake range over temperature.F3 E3Clean range over temperature.F3 E4Oven sensor opened F3 E5Oven sensor shorted F3 E6Warming drawer sensor open.F3 E7Warming drawer sensor shorted.F3-E0Shorted key / Stuck key.F3-E1Keytail unplugged.F5 E0Door switches do not agree.F5 E1Door latch not operating.F5 E2Latch error during CLEAN.F5-E0Oven sensor opened.F5-E0 (door)Door and switches do not agree.F5-E1Oven sensor shorted.F5-E1 (latch)Door latch not operating.F5-E2BAKE/BROIL range over temperature.

View all 34 error codes

F5-E2 (latch)Latch error during CLEAN.F5-E3CLEAN range over temperature.F8 E0N/A (no likely failure condition described).PFA reset has occurred in the Electronic Range Control (ERC), typically caused by…

Service modes (6)

Last Error Code RecallPress and hold the CANCEL/OFF key for 5 seconds until the last error code is displayed.
Last Fault Code RecallPress and hold CANCEL/OFF key for 5 seconds to display the last error code.
Temperature Adjustment (Temperature Knob)Press and hold CLOCK pad for 5 seconds
Temperature Adjustment (Touch Pads Only)Press and hold BAKE pad for 5 seconds
Test mode (diagnostic)Within 60 seconds of power up, simultaneously hold down the BAKE and CLOCK keys for 5 seconds
Test/Diagnostic ModeWithin 60 seconds of power up, simultaneously hold down the BAKE and CLOCK keys for 5 seconds. The…

Full entry steps, exit procedures, and test sequences are available in Max.

Related Whirlpool range models

78,000+ service manuals · 160,000+ error codes · 55+ brands

$29/month · Cancel anytime · Or $9.95 3-day pass