mypros+
Model reference

Whirlpool W10323648

Range

2 documents30 error codes11 service modes

Available documentation

Tech Sheet

  • Tech Sheet - W10323648 - Rev A16 pg
    Covers this model

Service Manual

  • Troubleshooting Gas and Electric Freestanding Range Electronic Controls70 pg
    Covers this model
MyPros+ Max

Diagnose your Whirlpool W10323648.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (30)

CodeMeaning
F1Control failure or UL A/D error(s) detected in the control board.F1 E*Control board failure (all F1 sub-codes indicate control fault).F1-E0EEPROM communication error (cooktop control).F1-E1Upper RTD uncalibrated (oven control).F1-E2Lower RTD uncalibrated (oven control).F1-E5Sensor usage out of range (oven control).F1-E7PCB thermistor/sensor open or shorted (cooktop control).F1-E9WIDE Queue full (oven control).F2Shorted/stuck key detected on the control keypad.F2-E0Keypad disconnected (oven control).F2-E1Stuck key (oven control).F2-E2Stuck key (oven control).F3Oven sensor opened or oven sensor shorted.F3 E0Oven temperature sensor fault (open or shorted)F3 E1Lower oven temperature sensor fault (MRC II double oven models).F3 E2Warming drawer temperature sensor fault.F3-E0Main oven temperature sensor open or shorted (upper oven).F3-E1Main oven temperature sensor open or shorted (lower oven).F5 E0Door position switch faultF5 E1Door latch switch/system faultF5 E2Door switch fault.F5-E0Door and latch switches do not agree during Clean mode.F5-E1Door latch not operating during Clean mode.F6 E*Control communication failure.F6-E0Lost communications between controls.F6-E1Over temperature condition during cook mode (runaway temp).F6-E2Over temperature condition during clean mode (runaway temp).F6-E3Over temperature condition in warming drawer (runaway temp).F9House miswiredF9-E0Range is mis-wired (product miswired).

Service modes (11)

  • Diagnostics Mode (Cooktop Controls)Press any 3 different keys in sequence
  • Diagnostics Mode (Oven Controls)Press CANCEL > CANCEL > START within 5 seconds.
  • LCC Diagnostic Mode (LCC90/LCC95/LCC180)["Press CANCEL, CANCEL, START in sequence.","Press TEMP/TIME '+' key to cycle through diagnostic…
  • LCC190 Diagnostic Mode (Self Clean, Convection models)["Press CANCEL, CANCEL, START in sequence.","Press TEMP/TIME or TEMP/HOUR '+' key to cycle through…
  • MRC Diagnostic Mode["Press CANCEL, CANCEL, START in sequence.","Press TEMP/TIME '+' key to cycle through diagnostic…
  • MRC Diagnostic Mode (Fan/True Convection Electric - Oven Light entry)["Press CANCEL, CANCEL, START in sequence.","Press TEMP/TIME '+' key to cycle through diagnostic…
  • MRC II Diagnostic Mode (Number 3 key entry - KitchenAid models)["Press OFF/OFF/START or CANCEL/CANCEL/START in sequence.","Press the number '3' key to cycle…
  • MRC II Diagnostic Mode (TEMP/TIME entry)["Press CANCEL, CANCEL, START in sequence.","Press TEMP/TIME '+' keypad to cycle through diagnostic…
  • Semi Automatic Test Mode (Oven Controls)1
  • Temperature CalibrationPress SETTINGS/OPTIONS until 'Temp Calib' is highlighted, then follow instructions to see the…
  • Test Mode (Oven Controls)1

Full entry steps, exit procedures, and test sequences are available in Max.

Related Whirlpool range models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass