mypros+
Model reference

Whirlpool YWFE770H0FZ0

Range

3 documents26 error codes15 service modes

Available documentation

Tech Sheet

  • TechSheet-W10843072-RevA(FR).pdf8 pg
    Covers this model
  • TechSheet-W10843071-RevA.pdf8 pg
    Covers this model
  • Wiring Diagram - W10843087 - Rev A2 pg
    Covers this model
MyPros+ Max

Diagnose your Whirlpool YWFE770H0FZ0.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (26)

CodeMeaning
F1-E0EEPROM communication error within the MRC control.F1-E5Sensor out of range detected by MRC control.F1-E7PCB thermistor open or shorted.F1E0EEPROM communication error.F1E5Sensor out of range.F1E7Circuit board thermistor open or short-circuited.F2-E0Keypad disconnected from control.F2-E1Stuck key detected on the keypad.F2-E2Cancel key error on the keypad.F2E0Keypad disconnected.F2E1Key stuck.F2E2Cancel key error.F3-E0Main oven temperature sensor open or shorted.F3-E2Warming drawer temperature sensor open or shorted.F3E0Main oven sensor open or short-circuited.F3E2Warming drawer sensor open or short-circuited.F5-E0Door and door position switch do not agree during Clean mode.F5-E1Door latch not operating during Clean mode.F5E0Door and switch mismatch (clean mode, on some models).F5E1Door latch not functional (clean mode, on some models).F6-E1Over temperature condition during cook mode.F6-E2Over temperature condition during clean mode.F6-E3Over temperature condition in warming drawer.F6E1Bake mode over-temperature condition.F6E2Clean mode over-temperature condition.F6E3Warming drawer over-temperature condition.

Service modes (15)

  • Auto TestAfter entering diagnostic mode (CANCEL>CANCEL>START), press the up arrow, '+', or '3' key to scroll…
  • CONTROL RESET["Enter Diagnostics mode (CANCEL > CANCEL > START)","Scroll to CONTROL RESET"]
  • Diagnostic / Service ModePress CANCEL > CANCEL > START
  • Diagnostics Mode (Service Mode Entry)["Press CANCEL","Press CANCEL","Press START","Display shows 'TEST ON' with cavity temperature and…
  • DISPLAYFrom diagnostic mode, scroll to step 5 (DISPLAY).
  • ENG MODE["Enter Diagnostics mode (CANCEL > CANCEL > START)","Scroll to ENG MODE","Press START to…
  • ENG MODE (Engineering Mode)From diagnostic mode, scroll to step 2 (ENG MODE)
  • FAULTSFrom diagnostic mode, scroll to step 7 (FAULTS).
  • RELAY USAGEFrom diagnostic mode, scroll to step 8 (RELAY USAGE).
  • Temperature Adjustment["Press OVEN LIGHT for 5 seconds (current offset or 0° is shown in display)","Press 'More'/'Less'…
  • TEST MODEFrom diagnostic mode, scroll to step 3 (TEST MODE)
  • TEST ON (Relay Checks)["Enter Diagnostics mode (CANCEL > CANCEL > START)","At the TEST ON screen, press specific keys to…
  • TEST ON (Relay Control)Displayed immediately upon entering diagnostic mode (CANCEL>CANCEL>START)
  • USAGEFrom diagnostic mode, scroll to step 1 (USAGE) using up arrow, '+', or '3'.
  • VERSIONFrom diagnostic mode, scroll to step 4 (VERSION).

Full entry steps, exit procedures, and test sequences are available in Max.

Related Whirlpool range models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass