mypros+
Error code reference

Samsung Washer Error Code bE1

Switch error

Samsung codesSamsung washer codes
Avg. service call
$285
National average. Trip fee plus diagnostic plus labor. Before parts.
MyPros+ 3-day pass
$9.95
Same diagnostic steps, on your phone. Start now.
You keep in your pocket
~$275
Even before you buy the part.
Skip the service call. Fix it yourself.
Full procedure unlocks instantly.
Get Started

What the bE1 error code actually means

Your Samsung washer thinks the power button has been held down for too long, which is usually caused by the button being stuck or the control panel being bent or assembled incorrectly. This is not a water or motor problem, it is a control panel issue. A technician will need to inspect the buttons and the board behind the control panel to find what is physically causing the button to register as stuck.

Diagnostic procedure

The full bE1 procedure

Step 1 is visible so you can confirm you are on the right page. The remaining steps, the ones that tell you whether to actually replace a part, unlock with any pass.

MyPros+ · DiagnosticsStep 1 preview
1
First diagnostic step
Check whether Power switch or tact switch is continually pressed; check if sub PBA holding screws are fastened too tightly.
Unlock with pass
Unlock with pass
Unlock with pass
More steps, wiring diagram references, and verified part numbers
Includes expected resistance and voltage values, connector pinouts, and supersession notes for replacement parts.
Unlock bE1 procedure $9.95

Or subscribe: $29/month for unlimited access to all codes plus Max AI diagnostics.

Most common causes of bE1

Ranked by how often they cause this code
  1. 1Overtightened sub PBA mounting screws
  2. 2Deformed or warped control panel
  3. 3Stuck or physically jammed power button
  4. 4Faulty tact switch on the sub PBA
  5. 5Improper control panel reassembly after prior service

Most DIYers save hundreds by diagnosing before ordering parts.

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass

Questions people ask about bE1

What does bE1 mean on a Samsung washer?
The bE1 code means the washer has detected that the power button or tact switch on the control panel has been in a continuously pressed state for more than 12 seconds. This is classified as a switch error. It is typically caused by a stuck button, a deformed control panel pressing against the button, or the sub PBA board being warped due to overtightened mounting screws.
Is it safe to use my washer while the bE1 code is showing?
The bE1 error relates to the control panel switch input and will typically prevent normal operation from starting. You should not attempt to force the machine to run while this fault is active. Resolve the underlying cause before using the washer to avoid potential control board damage from the unresolved switch fault.
How much does it cost to repair a bE1 error on a Samsung washer?
Cost depends on the root cause. If only screw tension adjustment or panel realignment is needed, the repair may cost very little beyond a service call fee, typically in the range of $75 to $150. If the sub PBA or the control panel fascia needs to be replaced, parts and labor combined can range from $150 to $350 or more depending on the specific model and local labor rates.
Can I fix the bE1 error myself?
Some causes of the bE1 error are DIY-accessible. You can inspect the control panel for visible warping, check that the power button moves freely without sticking, and verify that the sub PBA screws are not overtightened. If the issue is a failed tact switch or a cracked control panel, replacement parts will be needed and the repair may require disassembling the control panel housing.
Will resetting the washer clear the bE1 error?
A power reset may temporarily clear the bE1 code if the fault was caused by a transient event, but it will return immediately if the physical cause is still present. If the control panel is deformed, a button is stuck, or the sub PBA screws are overtightened, the error will reappear as soon as the washer powers on. The root hardware issue must be corrected for the code to stay clear.

Related Samsung washer error codes

All Samsung washer codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass