mypros+
Error code reference

Samsung Washer Error Code LC2

Water leakage check

Avg. service call
$285
National average. Trip fee plus diagnostic plus labor. Before parts.
MyPros+ 3-day pass
$9.95
Same diagnostic steps, on your phone. Start now.
You keep in your pocket
~$275
Even before you buy the part.
Skip the service call. Fix it yourself.
Full procedure unlocks instantly.
Get Started

What the LC2 error code actually means

Your Samsung washer has detected a water leak somewhere inside the machine, likely caused by a damaged internal hose or a part that is not properly connected. This is different from water overflowing the drum and usually means something inside the cabinet is leaking. You should stop using the washer until the source of the leak is found and repaired to avoid water damage to your home or further damage to the machine.

Diagnostic procedure

The full LC2 procedure

Step 1 is visible so you can confirm you are on the right page. The remaining steps, the ones that tell you whether to actually replace a part, unlock with any pass.

MyPros+ · DiagnosticsStep 1 preview
1
First diagnostic step
Check for alien substance in Draining Bellows; check if drain motor is defective.
More steps, wiring diagram references, and verified part numbers
Includes expected resistance and voltage values, connector pinouts, and supersession notes for replacement parts.
Unlock LC2 procedure $9.95

Or subscribe: $29/month for unlimited access to all codes plus Max AI diagnostics.

Most common causes of LC2

Ranked by how often they cause this code
  1. 1Foreign object in draining bellows
  2. 2Defective drain motor
  3. 3Cracked or damaged internal hose
  4. 4Improperly assembled hose connection
  5. 5Loose or misaligned internal component assembly

Most DIYers save hundreds by diagnosing before ordering parts.

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass

Questions people ask about LC2

What does LC2 mean on a Samsung washer?
LC2 on a Samsung washer indicates a secondary water leakage detection event tied to an internal hose defect or a part assembly issue inside the machine. The washer's leak detection system has sensed moisture accumulating inside the cabinet. This code specifically points to internal structural causes rather than an overflow condition. The draining bellows and drain motor are the first components to check.
Is it safe to run my Samsung washer when it shows LC2?
No, you should not continue running the washer while LC2 is active. An internal water leak can cause electrical hazards if water contacts wiring or control boards inside the cabinet. Continued use can also worsen water damage to your home's flooring or subfloor. Disconnect the washer and investigate the source of the leak before running another cycle.
Will resetting my Samsung washer clear the LC2 error code?
A basic reset may temporarily clear the LC2 code from the display, but it will not resolve the underlying leak. If the internal leak source is not corrected, the code will return as soon as the washer detects moisture again. The leak must be physically diagnosed and repaired before the error will stay cleared. Resetting without repairing also risks further water damage inside the machine or to your home.
How do I fix an LC2 error on my Samsung washer?
Start by inspecting the draining bellows for any foreign objects or debris that may be preventing a proper seal. Next, check the drain motor for signs of failure and verify that all internal hoses are fully seated and their clamps are tight. If a damaged hose or defective motor is found, that component will need to be repaired or replaced to clear the error.
How much does it cost to repair an LC2 error on a Samsung washer?
Repair costs vary depending on the root cause. If the issue is simply a foreign object in the draining bellows or a loose hose clamp, the fix may cost little to nothing beyond a service call fee, typically in the range of $75 to $150. Replacing a defective drain motor or a damaged internal hose, including parts and labor, can range from $150 to $350 depending on your location and the specific parts required.

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass