Amana OH-112E-C/P96363-4F

Available documentation

Error codes (56)

Service modes (36)

• Adaptive Defrost Control Test["Disconnect unit from the power source.","Open fresh food door and remove any items on the top…
• Automatic Function TestWith door latched, press key pads in the following sequence within 10 seconds
• Controller Self Diagnostic Test["With the oven door open, connect the power cord.","Verify colon only appears in the…
• Cook Count Mode["Open the oven door and leave open.","Enter the access code '613' by pushing buttons 6, 1, and…
• Customer-Focused Dryness Level Adjustment["In standby mode (dryer plugged in but not powered up), press and hold the DRYNESS LEVEL button…
• diagnosticWithin 10 seconds, press the following sequence of keys
• Diagnostic Mode (LCD models)["Enter service mode first","Rotate timer dial through positions to access different diagnostic…
• Fault Code Display / Clearing["Enter Service Diagnostic Mode.","If saved fault code exists, it will be flashing in the display…
• Idle/Service Mode (MAH5500B/MAH6500)["With washer in Off position, press and hold the Fabric Selection button and the Options…
• In-Cabinet Function Test (ICFT)["Ensure compressor is running (not in defrost), fresh food door is open, CZT assembly has power…
• Install Diagnostics["Activate Service Diagnostic Mode first.","Press and release the 2nd button used to activate…
• Key Activation & Encoder Test["First activate Service Diagnostic Mode.","Press and release the 1st button used to activate…
• Lid Switch Test["Press POWER to turn on the washer.","Press and hold CYCLE while pressing START three times.","A…
• Loads Test Mode["Ensure dryer is in standby mode (plugged in with all indicators off).","Within 5 seconds, press…
• Manual defrost initiationInsert a screwdriver blade into the slot on the main gear shaft of the mechanical defrost timer and…
• Manual Function TestWith door latched, press key pads in the following sequence within 10 seconds
• Manual Load Test["Tub must be empty of clothes and water before running this test.","Press and hold CYCLE and turn…
• Motor and Motor Control Test["1
• Motor and Motor Control Test (Delay Mode Test)["Set the timer knob into the delay increments.","Press the push-to-start switch to start the…
• Motor Phase Test["1
• Programming Mode["Open the oven door and leave open.","Enter the programming code '614' by pushing buttons 6, 1…
• Quick Service Test (MAH5500/MAH6500 - LCD models)["1. Turn cycle selector knob to a position.","2. Press and hold the Start/Stop button.","3. The…
• Quick Spin Test (LCD models)["Enter service mode","Set timer to appropriate position for spin test","Washer will execute spin…
• rapid_advanceAfter a cycle has started, enter the key sequence
• sales_demoWithin 10 seconds, press the following sequence of keys
• Scrolling Message Programming Mode["Open the oven door, leave open.","Press buttons 6, 1, and 5.","Close the oven door
• Service Calibration["Enter Service Test Mode.","Select function number 052 using Soil Level/Temp buttons or cycle…
• Service Diagnostic Mode["Ensure washer is in standby mode (plugged in with all indicators off).","Select any three (3)…
• Service Diagnostics (Automated Test Cycle)["Enter Service Test Mode.","Select function number 051 using Soil Level/Temp buttons or cycle…
• Service Mode (MAH5500/MAH6500 - LCD models)["Set timer to any Off position","Press and hold the Fabric Selection and Options buttons…
• Service Test Mode (Load Control)["First activate Service Diagnostic Mode.","Press and release the 2nd button used to activate…
• Software Version Display["First activate Service Diagnostic Mode.","Press and hold the 2nd button used to activate Service…
• Spin Test["Press POWER to turn on the washer.","Press and hold '+' while pressing START three times.","A…
• UI/LED Test["Press POWER to turn on the washer.","Press and hold LOAD while pressing START three times.","A…
• User Interface Test["Activate Service Diagnostic Mode first.","Press and release the 1st button used to activate…
• Volume Adjustment Mode["Open the door, leave open.","Press buttons 6, 1, 6.","Close the door

Full entry steps, exit procedures, and test sequences are available in Max.