Model reference
Amana OH-125/P96236-5F
Furnace
6 documents78 error codes21 service modes
Available documentation
Service Manual
- Service Manual - RS210000570 pg
- Service Manual - RS210000872 pg
Tech Sheet
- Tech Sheet - W11087920 - Rev A60 pg
- Tech Sheet whirlpool dryer W10606148 Rev C60 pg
- Tech Sheet - W10403269 - Rev A52 pg
Installation Guide
- Installation Instructions18 pg
MyPros+ Max
Diagnose your Amana OH-125/P96236-5F.
- Step-by-step diagnostics from the service manual
- Test values, resistance specs, and wiring references
- Verified part numbers when replacement is needed
Start diagnosing
$29/month · Cancel anytime · Or $9.95 3-day pass
Error codes (78)
CodeMeaning
1-1Control detected K2 pilot relay stuck closed.1-2Damaged or corrupted memory on control board, or incompatible software…10-1Dispenser electrical problem; loose connection in dispenser circuit and/or open…10-2Vent wax motor electrical problem; loose connection in vent circuit and/or open…10-3Drying fan error; loose connection in fan circuit and/or open fan motor.2-1Stuck key(s) detected in keypad or keypad connection.2-2User interface cannot communicate with the main control board; incorrect…3-1Open connector or component in temperature sensing circuit; open or faulty…3-2Incoming water temperature above 167°F (75°C), or shorted connection/component…3-3OWI failed calibration.4-3Wash motor not running due to loose connection in wash motor circuit and/or…5-1Door stuck open; door was not latched within 3 seconds of pressing Start/Resume…5-2Door stuck closed; control programmed to not start if it suspects door switch…6-1Low/no water (mechanical problem); no water supply to dishwasher or various…6-2Fill valve electrical problem; loose connection in fill valve circuit and/or…6-3Suds/air in pump; too many suds, captured wash water, water leak, or missing…6-4Float switch open; overfill switch stuck in overfill position and/or dishwasher…6-7Disconnected or damaged flowmeter.6-8Regen valve electrical problem; loose connection in regen valve circuit and/or…7-1No heat; control programmed to disable heater but continue running cycles if it…7-2Heater stuck on; heater drive circuit on the control is faulty.8-1Slow drain; obstructed drain hose or path, or drain pump impeller fractured.8-2Drain motor electrical problem; loose connection in drain motor circuit and/or…8-3Drain stuck on; drain motor drive circuit on the control is faulty.9-1Can't find diverter position; corroded or loose connection in diverter…9-2Diverter stuck on; diverter drive circuit on the control is faulty.9-3Control detected diverter disk in sump is missing.9-4Lower spray arm error; mechanical blockage or jammed lower spray arm, or…drnDrain pump system problemF0E2Oversuds condition detectedView all 78 error codes
F0E3Overload conditionF0E4Spin limited by water temperatureF0E5Off balance load condition detected.F1E1Main control fault (internal ACU failure).F1E2Motor control section of the main control has faulted.F1E3Mismatch of ACU and UIF2E1UI stuck buttonF2E2User Interface software errorF2E3UI mismatchF2E4UI software errorF2E5UI software errorF3E1Pressure system faultF3E2Inlet water temperature faultF3E3Inlet thermistor is open; temperature drops below 18°F (>245k ohms).F3E4Inlet thermistor is shorted; temperature above 391°F (<20 ohms).F3E5Inlet and exhaust thermistors are open; will occur if P14 connector is not…F3E6Moisture sensor strip is open; only appears in service diagnostic mode.F3E7Moisture sensor strip has shorted; only appears in service diagnostic mode.F4E1Heater stuck onF4E2Heater not turning onF4E3Restricted/low air flow that may affect dryer performance.F4E4Low L2 voltage (less than 50V) detected at installation.F5E1Lid switch faultF5E2Lid lock will not lock or lid lock failure.F5E3Lid lock will not unlock.F5E4Lid not opened between cyclesF6E1Communication between CCU and UI has not been detected (UI to CCU communication…F6E2Communication errorF6E3Communication errorF7E0Loss of powerF7E1Loss of power during spinF7E2Motor drive module failureF7E3Basket engaged during washF7E4Basket re-engagement failureF7E5Shifter failure.F7E6Motor circuit openF7E7Motor unable to meet target RPM.F7E8Motor over temperatureF7E9Locked rotorF8E1Long fillF8E3Overflow or flood conditionF8E6Water hazardF9E1Drain pump system problemF9E2Drain pump system problemFCE1WiFi Module communications lost.L2Low L2 voltage (less than 50V) detected at installation.LFLong fillPFPower failure occurred while the dryer was running.
Service modes (21)
- Automatic Function TestWith door latched, press key pads in the following sequence within 10 seconds
- Component Activation / Quick Service Cycle (LCD in Door Models)["Enter Service Diagnostic Mode (LCD in Door) first.","From the DIAGNOSTICS HOME screen, scroll…
- Customer-Focused Dryness Level Adjustment1
- Fault Code Display / Clearing["Enter Service Diagnostic Mode.","If saved fault code exists, it will be flashing in the display…
- Install Diagnostics1
- Key Activation & Encoder Test["First activate Service Diagnostic Mode.","Press and release the 1st button used to activate…
- Key Activation & Encoder Test (Console Models)["Activate Service Diagnostic Mode first.","Press and release the 1st button used to activate…
- Loads Test Mode["Ensure dryer is in standby mode (plugged in with all indicators off).","Within 5 seconds: Press…
- Manual Function TestWith door latched, press key pads in the following sequence within 10 seconds
- Service Calibration["Enter Service Test Mode.","Select function number 052 using Soil Level/Temp buttons or cycle…
- Service Diagnostic Mode["Ensure washer is in standby mode (plugged in with all indicators off).","Select any three (3)…
- Service Diagnostic Mode (Console Models)["Ensure the dryer is in standby mode (plugged in with all indicators off).","Select any three (3)…
- Service Diagnostic Mode (LCD in Door Models)["Ensure the dryer is in standby mode (plugged in with all indicators off).","Open and close the…
- Service Diagnostics (Automated Test Cycle)["Enter Service Test Mode.","Select function number 051 using Soil Level/Temp buttons or cycle…
- Service Diagnostics CycleWhile in standby, press any 3 keys in the sequence 1-2-3-1-2-3-1-2-3 with no more than 1 second…
- Service Test Mode (Console Models)["Activate Service Diagnostic Mode first.","Press and release the 2nd button used to activate…
- Service Test Mode (Load Control)["First activate Service Diagnostic Mode.","Press and release the 2nd button used to activate…
- Software Version Display["First activate Service Diagnostic Mode.","Press and hold the 2nd button used to activate Service…
- Software Version Display (Console Models)["Activate Service Diagnostic Mode first.","Press and hold the 2nd button used to activate Service…
- User Interface Test["Activate Service Diagnostic Mode first.","Press and release the 1st button used to activate…
- User Interface/Control System Test1. Activate Service Diagnostic Mode. 2. Press and release the 1st button used to activate Service…
Full entry steps, exit procedures, and test sequences are available in Max.
Related Amana furnace models
78,000+ service manuals · 160,000+ error codes · 55+ brands
Get Started$29/month · Cancel anytime · Or $9.95 3-day pass