mypros+
Model reference

Amana OH-140-4

Furnace

4 documents26 error codes17 service modes

Available documentation

Tech Sheet

  • tech sheet 160232138 pg
    Covers this model

Tech Tip

  • Instruction Sheet2 pg
    Covers this model

Installation Guide

  • Installation Instructions12 pg
    Covers this model
  • Installation Instructions9 pg
    Covers this model
MyPros+ Max

Diagnose your Amana OH-140-4.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (26)

CodeMeaning
160° Rinse LED + Clean LEDMotor low current condition detected during Field Service Test.Extra Rinse LED + Clean LEDTurbidity Sensor failure detected during Field Service Test.F0E2Over suds condition detectedF0E4High water temperature detected (105°F or higher) during rinse cycle.F0E5Off balance load detected during operation.F1E1Main control fault detected.F1E2Motor control faultF2E1Stuck keyF2E3Mismatch of main control and UIF3E1Pressure system faultF3E2Inlet water temperature faultF5E1Lid switch faultF5E2Lid lock faultF5E3Lid unlock faultF5E4Lid not opened between cyclesF7E1Basket speed faultF7E5Shifter faultF7E6Motor faultF7E7Motor unable to reach target RPMF8E1No fill / long fillF8E3Overflow conditionF8E5Hot and cold reversedF9E1Long drainHeated Dry LED + Clean LEDMemory failure detected during Field Service Test.Sanitize LED + Clean LEDThermistor failure detected during Field Service Test.Super Scrub LED + Clean LEDMotor high current condition detected during Field Service Test.

Service modes (17)

  • Automatic Test Mode["Enter Service Diagnostic Test Modes.","Turn cycle selector knob until the 'Spin' LED is ON (all…
  • Calibration Mode["Enter Service Diagnostic Test Modes.","Turn cycle selector knob until 'Rinse' LED is ON (all…
  • Fault Code Display Mode["Enter Service Diagnostic Test Modes.","Turn cycle selector knob until the 'Done' LED is ON (all…
  • Field Service TestPress the Heated Dry button 5 times followed by the Start button within 6 seconds.
  • Forced Defrost ModeRefer to Control Board section, page 36 of service manual for specific button sequence (not…
  • Manual Function TestPress the SANITIZE button 5 times followed by the Start button within 6 seconds.
  • Manual Test Mode["Enter Service Diagnostic Test Modes.","Turn cycle selector knob until 'Spin' and 'Done' LEDs are…
  • Programming ModeRefer to Control Board section, page 36 of service manual for specific button sequence (not…
  • Sabbath ModeAccess User Preferences menu (press and hold Door Alarm pad for 3 seconds), scroll to SAb using…
  • Sales Floor Demo ModePress Extra Rinse button 5 times within 6 seconds.
  • Service Diagnostic Test Modes (Entry)["Ensure washer is in standby mode (plugged in with all indicators off).","Wait 10 seconds after…
  • Service Test ModeRefer to Control Board section, page 36 of service manual for specific button sequence (not…
  • Show Room ModeRefer to Control Board section, page 40 of service manual for specific button sequence (not…
  • Software Version Display Mode["Enter Service Diagnostic Test Modes.","Turn cycle selector knob until 'Rinse', 'Spin', and 'Done'…
  • Tachometer Verification Mode["Enter Service Diagnostic Test Modes.","Turn cycle selector knob until 'Wash' and 'Done' LEDs are…
  • UI Test Mode["Enter Service Diagnostic Test Modes.","Turn cycle selector knob until 'Rinse' and 'Spin' LEDs are…
  • User Preferences MenuPress and hold the Door Alarm pad for three seconds

Full entry steps, exit procedures, and test sequences are available in Max.

Related Amana furnace models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass