Model reference
Amana YY-100-MA
Furnace
5 documents71 error codes25 service modes
Available documentation
Tech Sheet
- Tech Sheet - 97603318 pg
- Tech Sheet - 97613898 pg
Service Manual
- service manual W1133862052 pg
Tech Tip
- Instruction Sheet - 85290016 pg
- Instruction Sheet - 3979706 - Rev A8 pg
MyPros+ Max
Diagnose your Amana YY-100-MA.
- Step-by-step diagnostics from the service manual
- Test values, resistance specs, and wiring references
- Verified part numbers when replacement is needed
Start diagnosing
$29/month · Cancel anytime · Or $9.95 3-day pass
Error codes (71)
CodeMeaning
E0Manufacturing codeE1Manufacturing codeE2Manufacturing codeE3Manufacturing codeE4Ice maker errorE5Ice maker errorE6Manufacturing codeErManufacturing codeF0-E0No failureF0E0No failure (displayed only if user presses and holds CANCEL/OFF key for 5…F1 E0EEPROM communications error.F1 E1EEPROM checksum error.F1-E0EEPROM communications error.F1-E1EEPROM checksum failure.F1-E2UL A/D error(s).F1-E3Fuel type (gas/electric) select failure.F1E0EEPROM communications failure.F1E1EEPROM checksum failure.F1E2Internal error (display board related).F1E3Fuel type (gas/electric) select failure.F1E4Microwave ACU PCBA failure.F1E5Internal error (power board related).F1E6Internal error (power board related).F1E7Internal error (power board related).F1E8Internal error (power board related).F1E9Internal error (display board related).F2 E2UL A/D error(s).F2-E0Shorted key.F2-E1Keytail unplugged.F2-E6CANCEL key failure.View all 71 error codes
F2E0Key held down too long or shorted key.F2E1Keytail unplugged or damaged.F2E6CANCEL key failure.F3 E0Shorted key.F3 E1Key tail unplugged.F3-E0Oven sensor opened.F3-E1Oven sensor shorted.F3-E2BAKE/BROIL range over temperature.F3-E3CLEAN range over temperature.F3E0Oven sensor opened.F3E1Oven sensor shorted.F3E2BAKE/BROIL range over temperature.F3E3CLEAN range over temperature.F3E4Bottom oven temperature sensor open (bottom oven sensor open).F3E5Bottom oven temperature sensor shorted (lower oven sensor shorted).F3E6Warming drawer temperature sensor open.F3E7Warming drawer temperature sensor shorted.F4E2Over temperature during cook mode.F4E3Over temperature during clean mode.F4E4Humidity sensor error.F4E7Over temperature cavity 2 (temperature runaway error).F4E9Smart pop error.F5 E0Oven sensor opened.F5 E0 (door)Door switches do not agree.F5 E1Oven sensor shorted.F5 E1 (door)Door latch not operating.F5 E2Bake/broil range over temperature.F5 E2 (door)Latch error during clean.F5 E3Clean range over temperature.F5-E0Door and switches do not agree.F5-E1Door latch not operating.F5-E2Latch error during CLEAN.F5E0Door switches do not agree.F5E1Door latch not operating.F5E2Latch error during CLEAN.F5E4Latch switch fault.F5E7Unlock door errorF6E0ACU PCBA communication failure.F6E4Lost communication between power board and display board.F6E5Cancel key error.F8E5Exhaust air temperature detection failure from Hood NTC thermistor.
Service modes (25)
- 12 hour shut offPress and hold CLOCK pad for 5 seconds.
- 12 Hour Shut-off TogglePress and hold CLOCK key for 5 seconds.
- Audible pitch controlPress and hold DELAY START TIME key for 5 seconds.
- Audible signal pitch controlPress and hold DELAY START TIME pad for 5 seconds.
- Cooktop LockoutPress and hold the TOP/TOP LIGHT keypad on the control panel for 5 seconds
- Cooktop Lockout FeaturePress and hold TOP/TOP LIGHT keypad on control panel for 5 seconds
- Diagnostic mode["Press the Cancel key to place the range in an idle state.","Press the Cancel and Start keys in…
- Diagnostics / Test Mode["Plug in microwave oven or reconnect power.","Press Cancel button to reach standby display (colon…
- Diagnostics Mode1. Plug in microwave oven or reconnect power and press CANCEL button to standby (':'). 2. Close…
- Disable/Enable All Tones (except end-of-timer and error tones)Press and hold COOK TIME key for 5 seconds.
- Disable/Enable all tones except end-of-timer and error tonesPress and hold COOK TIME pad for 5 seconds.
- Disable/Enable cycle and timer-end repeating tonesPress and hold TIMER SET pad for 5 seconds.
- Fahrenheit to Celsius conversionPress and hold BROIL pad for 5 seconds.
- Forced Defrost Mode (Service Test 38)1. Enter Service Diagnostics Mode. 2. Navigate to Step 38. 3. Select SW3 to toggle
- Fuel type verificationPress and hold START/ENTER key for 5 seconds until fuel type is displayed
- Hidden EOC FunctionsPress and hold the appropriate key for 5 seconds to activate each hidden function. Functions…
- Last Error Code RecallPress and hold CANCEL/OFF key for 5 seconds until last error code is displayed.
- Oven Temperature Calibration AdjustmentPress and hold BAKE pad for 5 seconds. Current offset is shown in 3-digit display; 'CAL' is shown…
- Recall last failure codePress and hold CANCEL/OFF pad for 5 seconds until last error code is displayed.
- Sales Demonstration ModePress and hold TIMER OFF key for 5 seconds.
- Service Diagnostics Mode1
- Software revision numberPress and hold START/ENTER pad for 5 seconds
- Temperature Calibration Adjustment1. Press and hold BAKE pad for 5 seconds. Current offset (if any) is shown in 3-digit display; CAL…
- Temperature calibration offsetPress and hold BAKE pad for 5 seconds
- Verify fuel typePress and hold START/ENTER key for 5 seconds until fuel type is displayed
Full entry steps, exit procedures, and test sequences are available in Max.
Related Amana furnace models
78,000+ service manuals · 160,000+ error codes · 55+ brands
Get Started$29/month · Cancel anytime · Or $9.95 3-day pass