Model reference
GE ZET3058
Oven
7 documents19 error codes11 service modes
Available documentation
Service Manual
- Owner's Manual Self-Cleaning Oven with Trivection™ Built-In Oven48 pg
- TECHNICAL SERVICE GUIDE - 2003 Slide-In, Single and Double Wall Ovens with TrivectionTM Cooking77 pg
- GE Consumer Products Technical Service Guide 2003 Slide-In, Single and Double Wall Ovens with TrivectionTM Cooking77 pg
- TECHNICAL SERVICE GUIDE - Slide-In, Single and Double Wall Ovens with Trivection™ Cooking77 pg
Tech Sheet
- Appliance Diagnostic Modes Range GE Consumer & Industrial Technical Training255 pg
Installation Guide
- Installation Instructions - 30" Built-In Trivection™ Wall Oven16 pg
Other
- 319115GE2003SlideInSingleDblWallOvenswTrivectionCking77 pg
MyPros+ Max
Diagnose your GE ZET3058.
- Step-by-step diagnostics from the service manual
- Test values, resistance specs, and wiring references
- Verified part numbers when replacement is needed
Start diagnosing
$29/month · Cancel anytime · Or $9.95 3-day pass
Error codes (19)
CodeMeaning
CONTROL IS LOCKEDControl lockout is active; touch pads cannot be activated when pressed.ENTERING SALES MODEDuring power-up, L1-L2 is between 90VAC and 150VAC and L1-N is between 90VAC…ERRA temperature was set outside the allowable range of 170°F–550°F.FFunction error code indicated by F followed by a number or letter flashing in…F0Stuck key or shorted keypad detected on the control panel.F2Oven over-temperature condition detected by the control.F3Oven temperature sensor open circuit (open sensor).F4Oven temperature sensor shorted circuit (shorted sensor).F5Sensor circuit supervisor failure in the control board.F7Stuck or shorted function key on the keypad.F8Control board failure (internal ERC fault).F9Thermal switch (FAD TCO) has opened in any mode of operation, indicating a…FFLoss of latch motor safety circuit.LOW POWERAfter power-up, L1-L2 voltage drops below 150VAC during operation.MISWIRED DETECTEDWiring from house to oven is incorrect.OVEN TOO HOTProofing will not operate when oven is above 125°F.SENSE 120V ENTERING SALES MODEDuring power-up, L1-L2 is between 90VAC and 150VAC and L1-N is between 90VAC…SUPPLY MISWIREDPower monitor detects miswired supply; L1-L2 is below 90VAC while L1-N is above…SUPPLY OPEN NEUTRALPower monitor detects open neutral condition; L1-N voltage is below 90VAC.Service modes (11)
- Factory Mode (Control Type Re-entry)["Enter special modes screen by pressing 0803 within 5 minutes of reconnecting power.","Press…
- Factory Mode (Control Type Selection)["Reconnect power to the oven.","Enter 0803 within 5 minutes of reconnecting power.","Press…
- Factory Mode (Oven Type Selection)["Within 5 minutes of reconnecting power, enter 0803 on the keypanel.","Press Factory1 to enter the…
- J2S968/JGS968/JGSP48 Fault Code Recall["Press TIMER, CLOCK, and MIN DOWN (or 9) key to get Fault Codes to appear."]
- JB905/968/988 Fault Code Recall["Press TIMER and CLOCK (or 9) key to get Fault Codes to appear."]
- JP938/JP968 Cooktop Calibration Mode["Clear everything from the top of the glass.","Lock the control by pressing the LOCK key for 3…
- JP938/JP968 Cooktop Technician Mode["Lock cooktop by holding CONTROL LOCK key for 3 seconds.","Control will beep 2 times and LOCK…
- LOC REF Procedure (JCK915/JCT915/JK915/JT915/JK955/JT955/ZEK938/ZET958)["Reinitiate LOC REF procedure by pressing BAKE/BROIL simultaneously.","For digital keypads press 9…
- Sales Mode["Power up with 120V only (L1-L2 = 120V, L2 connected to N).","Requires special 120 VAC cord (Wall…
- Service Mode["Disconnect main power to the oven for at least 15 seconds.","Reconnect power.","Enter 0803 on the…
- Trivection Service Mode["Disconnect main power to the oven for at least 15 seconds.","Reconnect power and enter 0803 on…
Full entry steps, exit procedures, and test sequences are available in Max.
Related GE oven models
78,000+ service manuals · 160,000+ error codes · 55+ brands
Get Started$29/month · Cancel anytime · Or $9.95 3-day pass