Model reference
KitchenAid KDTE234GPS0
Dishwasher
6 documents50 error codes6 service modes
Available documentation
Service Manual
- jobaid w10573282120 pg
- 2013 Stainless Steel Tall Tub Dishwasher120 pg
Tech Sheet
- Tech Sheet W11427956A16 pg
- Tech Sheet W10904613 RevB68 pg
Wiring Diagram
- KDTE204ESS4 Wiring Diagram W10921454 RevA2 pg
Tech Tip
- Instruction Sheet2 pg
MyPros+ Max
Diagnose your KitchenAid KDTE234GPS0.
- Step-by-step diagnostics from the service manual
- Test values, resistance specs, and wiring references
- Verified part numbers when replacement is needed
Start diagnosing
$29/month · Cancel anytime · Or $9.95 3-day pass
Error codes (50)
CodeMeaning
1-1Control detected K1 pilot relay stuck closed.1-2Control software issue10-1Dispenser electrical problem10-3Drying fan error2-2No response from User Interface (UI)3-1Thermistor/OWI open3-2Thermistor/OWI shorted3-3Thermistor/OWI failed calibration4-3Wash motor not running5-1Door switch stuck open5-2Door switch stuck closed6-1Inlet water low/no water (mechanical problem)6-2Fill valve electrical problem6-3Suds/air in pump6-4Float switch open7-1No heat7-2Heater stuck on8-2Drain motor electrical problem8-3Drain stuck on9-1Diverter can't find position9-2Diverter stuck on9-3Diverter disc missingF10E1OtherF10E2Vent wax motor electrical problemF10E3OtherF1E1ControlF1E2ControlF2E1Control detected stuck key(s) in keypad or keypad connection.F2E2User interface cannot communicate with main control; loose user interface…F3E1Open connection or component in temperature sensing circuit; open or faulty…View all 50 error codes
F3E2Shorted connection or component in temperature sensing circuit; incoming water…F3E3OWI calibration failure.F4E4Wash motor failure due to loose connection in wash motor circuit and/or open…F5E1Door was not latched within 3 seconds of pressing Start/Resume, or loose…F5E2Control suspects door switch is stuck closed; control programmed to not start…F6E1Inlet WaterF6E2Fill valve electrical problemF6E3Inlet WaterF6E4Inlet WaterF6E6Cool waterF7E1HeatingF7E2HeatingF8E1Slow drainF8E2DrainingF8E3DrainingF8E4Drain motor electrical problemF9E1DiverterF9E2DiverterF9E3DiverterF9E4Lower spray arm error
Service modes (6)
- Clear Customer Error HistoryDuring Service Diagnostic Cycle Interval 4, press HI TEMP key to clear customer error history.
- Rapid Advance (Customer Cycles)After starting a customer cycle, press HIGH TEMP
- Rapid Advance ModeAfter starting a cycle, press HI TEMP
- Rapid Advance Mode (during normal cycle)Press HI TEMP
- Service Diagnostic CycleWhile in Standby, press any 3 keys in the sequence 1-2-3-1-2-3-1-2-3 with no more than 1 second…
- Service Diagnostics CycleWhile in Standby mode, press any 3 keys in the sequence 1-2-3-1-2-3-1-2-3 with no more than 1…
Full entry steps, exit procedures, and test sequences are available in Max.
Related KitchenAid dishwasher models
78,000+ service manuals · 160,000+ error codes · 55+ brands
Get Started$29/month · Cancel anytime · Or $9.95 3-day pass