mypros+
Model reference

KitchenAid KUDE40FXSS4

Dishwasher

11 documents59 error codes8 service modes

Available documentation

Service Manual

  • 2013 Stainless Steel Tall Tub Dishwasher120 pg
    Covers this model

Tech Sheet

  • TechSheet W10455258 RevA FR2 pg
    Covers this model
  • Tech Sheet - W10195614 - Rev E (FR)2 pg
    Covers this model
  • Jennair Dishwasher JDB8500AWX3 W10455257 Tech Sheet2 pg
    Covers this model

Service Flash

  • ServicePointer W10547922 RevA Dishwasher OutletHoseClampReplacementKit3 pg
    Covers this model
  • Technical Service Pointer - W10475713 - Rev A (Vent Removed)3 pg
    Covers this model
  • Technical Service Pointer - Upper Rack Wheel & Mount Assembly9 pg
    Covers this model
  • Service Pointer - W10460581 (Moisture Detected Inside Door Panels)2 pg
    Covers this model
  • Single Pvc Toe/kick Panel and Plastic Retention Clips4 pg
    Covers this model

Other

  • Service Pointer - W10756177 - Rev B (Upper Rack Disengages)6 pg
    Covers this model
  • Service Pointer - W10460578 - Rev B (Latch Blocks Door From Closing)_W104605789 pg
    Covers this model
MyPros+ Max

Diagnose your KitchenAid KUDE40FXSS4.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (59)

CodeMeaning
1-1Control detected K2 pilot relay stuck closed.1-2Damaged or corrupted memory on control board or incompatible software…10-1Dispenser electrical problem10-2Vent wax motor electrical problem10-3Drying fan error2-1Control detected stuck key(s) in keypad or keypad connection.2-2No response from User Interface3-1Open connector or component in Temperature Sensing Circuit, or open/faulty…3-2Shorted connection or component in Temperature Sensing Circuit, shorted or…3-3OWI failed calibration.4-1No communication between control and wash motor.4-2Motor communication error between control and wash motor.4-4Wash motor failure5-1Door stuck open5-2Door stuck closed6-1Low/no water6-2Fill valve electrical problem6-3Suds/air in pump6-4Float switch open6-6Cool water6-7Flowmeter problem6-8Regen valve electrical problem7-1No heat7-2Heater stuck on8-1Slow drain8-2Drain pump impeller fractured.8-3Drain motor electrical problem8-3 (stuck on)Drain stuck on8-4Drain motor electrical problem9-1Diverter can't find position
View all 59 error codes
9-2Diverter stuck on9-3Diverter disk missing9-4Diverter problem (general).F10E1Dispenser electrical problemF10E2Vent wax motor electrical problemF10E3Drying fan errorF1E1Control detected K400 pilot relay stuck closed.F1E2Damaged or corrupted memory on control board; incompatible software components…F2E1Control detected stuck key(s) in keypad or keypad connection.F2E2User interface cannot communicate with main control; loose user interface…F3E1Open connection or component in temperature sensing circuit; open or faulty…F3E2Shorted connection or component in temperature sensing circuit; incoming water…F3E3OWI (Optical Water Indicator) failed calibration.F4E4Wash motor failure due to loose connection in wash motor circuit and/or open…F5E1Door was not latched within 3 seconds of pressing Start/Resume, or loose…F5E2Control programmed to not start if it suspects the door switch is stuck closed…F6E1Low or no water to dishwasher (mechanical problem)F6E2Fill valve electrical problemF6E3Suds or air detected in pumpF6E4Float switch stuck in overfill (open) position and/or dishwasher not level…F6E6Incoming water temperature under 18°C/65°F (cool water detected).F7E1No heatF7E2Heater stuck onF8E1Slow drainF8E4Drain motor electrical problemF9E1Diverter can't find positionF9E2Diverter stuck onF9E3Diverter disc missingF9E4Lower spray arm error

Service modes (8)

  • Clear Customer Error HistoryDuring Service Diagnostic Cycle Interval 4, press HI TEMP key to clear customer error history.
  • Clear Error HistoryDuring Service Diagnostics Cycle interval with Hi Temp LED on (10 seconds pause after Error 4)…
  • Error Code ReadingRun Service Diagnostics Cycle
  • Rapid Advance Mode["After starting a cycle, press HI TEMP
  • Rapid Advance Mode (during normal cycle)Press HI TEMP
  • Service Diagnostic CycleWith dishwasher in standby mode, press any 3 keys in the sequence 1-2-3, 1-2-3, 1-2-3 with no more…
  • Service Diagnostics CycleWhile in standby, press any 3 keys in the sequence 1-2-3-1-2-3-1-2-3 with no more than 1 second…
  • Service Diagnostics Rapid AdvanceDuring the Service Diagnostics Cycle, press Start/Resume key to advance 1 interval at a time.

Full entry steps, exit procedures, and test sequences are available in Max.

Related KitchenAid dishwasher models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass