Model reference
KitchenAid KUDE48FXBL6
Dishwasher
12 documents59 error codes9 service modes
Available documentation
Service Manual
- 2013 Stainless Steel Tall Tub Dishwasher120 pg
- 2013 Stainless Steel Tall Tub Dishwasher120 pg
Tech Sheet
- TechSheet W10455258 RevA FR2 pg
- Tech Sheet - W10195614 - Rev E (FR)2 pg
- Jennair Dishwasher JDB8500AWX3 W10455257 Tech Sheet2 pg
Bulletin
- Whirlpool Dishwasher Global Wash System Service Update10 pg
Service Flash
- ServicePointer W10547922 RevA Dishwasher OutletHoseClampReplacementKit3 pg
- Technical Service Pointer - W10475713 - Rev A (Vent Removed)3 pg
- Service Pointer - W10460581 (Moisture Detected Inside Door Panels)2 pg
Tech Tip
- Instruction Sheet2 pg
Installation Guide
- Installation Instructions Undercounter Dishwasher56 pg
Other
- W10460578B9 pg
MyPros+ Max
Diagnose your KitchenAid KUDE48FXBL6.
- Step-by-step diagnostics from the service manual
- Test values, resistance specs, and wiring references
- Verified part numbers when replacement is needed
Start diagnosing
$29/month · Cancel anytime · Or $9.95 3-day pass
Error codes (59)
CodeMeaning
1-1Control function error1-2Control function error10-1Other10-2Other10-3Other2-1User Interface2-2User Interface3-1Thermistor/OWI3-2Thermistor/OWI3-3Thermistor/OWI4-1No communication between control and wash motor.4-2Wash Motor4-4Wash Motor5-1Door Switch5-2Door Switch6-1Inlet Water6-2Inlet Water6-3Inlet Water6-4Inlet Water6-6Inlet Water6-7Flowmeter problem6-8Inlet Water7-1Heating7-2Heating8-1Draining8-2Draining8-3Draining8-3 (stuck on)Drain stuck on8-4Draining9-1DiverterView all 59 error codes
9-2Diverter9-3Diverter9-4DiverterF10E1Dispenser electrical problemF10E2Vent wax motor electrical problemF10E3Drying fan errorF1E1Control detected K400 pilot relay stuck closed.F1E2Damaged or corrupted memory on control board; incompatible software components…F2E1Control detected stuck key(s) in keypad or keypad connection.F2E2User interface cannot communicate with main control; loose user interface…F3E1Open connection or component in temperature sensing circuit; open or faulty…F3E2Shorted connection or component in temperature sensing circuit; incoming water…F3E3OWI (Optical Water Indicator) failed calibration.F4E4Wash motor failure due to loose connection in wash motor circuit and/or open…F5E1Door was not latched within 3 seconds of pressing Start/Resume, or loose…F5E2Control programmed to not start if it suspects the door switch is stuck closed…F6E1Low or no water to dishwasher (mechanical problem)F6E2Fill valve electrical problemF6E3Suds or air detected in pumpF6E4Float switch stuck in overfill (open) position and/or dishwasher not level…F6E6Incoming water temperature under 18°C/65°F (cool water detected).F7E1No heatF7E2Heater stuck onF8E1Slow drainF8E4Drain motor electrical problemF9E1Diverter can't find positionF9E2Diverter stuck onF9E3Diverter disc missingF9E4Lower spray arm error
Service modes (9)
- Clear Customer Error HistoryDuring Service Diagnostic Cycle Interval 4, press HI TEMP key to clear customer error history.
- Clear Error HistoryDuring Service Diagnostics Cycle interval with Hi Temp LED on (10 seconds pause after Error 4)…
- Error Code Display (within Service Diagnostics)After entering Service Diagnostics Cycle, errors are displayed in intervals 25-22. Interval 27
- Error Code ReadingRun Service Diagnostics Cycle
- Rapid Advance ModeAfter starting a cycle, press HI TEMP
- Rapid Advance Mode (during normal cycle)Press HI TEMP
- Service Diagnostic CycleWith dishwasher in standby mode, press any 3 keys in the sequence 1-2-3, 1-2-3, 1-2-3 with no more…
- Service Diagnostics Cycle1
- Service Diagnostics Rapid AdvanceDuring the Service Diagnostics Cycle, press Start/Resume key to advance 1 interval at a time.
Full entry steps, exit procedures, and test sequences are available in Max.
Related KitchenAid dishwasher models
78,000+ service manuals · 160,000+ error codes · 55+ brands
Get Started$29/month · Cancel anytime · Or $9.95 3-day pass