Model reference

KitchenAid KUDE60FXWH5

Dishwasher

12 documents56 error codes6 service modes

Available documentation

Service Manual

jobaid w10573282120 pg
Covers this model
2013 Stainless Steel Tall Tub Dishwasher120 pg
Covers this model
2013 Stainless Steel Tall Tub Dishwasher120 pg
Covers this model

Tech Sheet

TechSheet W10455258 RevA FR2 pg
Covers this model
Jennair Dishwasher JDB8500AWX3 W10455257 Tech Sheet2 pg
Covers this model

Service Flash

ProDry™ (with Fan Assist Operation) vs. non Fan Assist Models9 pg
Covers this model
Service Pointer - W10460581 (Moisture Detected Inside Door Panels)2 pg
Covers this model

Tech Tip

Instruction Sheet2 pg
Covers this model

Installation Guide

Installation Instructions Undercounter Dishwasher56 pg
Covers this model
Instruction Sheet1 pg
Covers this model
Instruction Sheet for Heater Element kit2 pg
Covers this model

Other

W10460578B9 pg
Covers this model

MyPros+ Max

Diagnose your KitchenAid KUDE60FXWH5.

Step-by-step diagnostics from the service manual
Test values, resistance specs, and wiring references
Verified part numbers when replacement is needed

Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

M+

M+ Max·KitchenAid Dishwasher

1-1 on my KitchenAid KUDE60FXWH5

M+

Control function error - Pilot relay

From Tech Sheet W14804357, p.49:

1.Access service mode to confirm the active fault code and read stored error history.

2.Measure control board supply voltage at test points. Expected: 12 VDC and 5 VDC.

3.Inspect all connectors on the main control for corrosion or backed-out pins.

Part WPW10804018

Electronic control board

Error codes (56)

View all 56 error codes

F10E1Dispenser electrical problem F10E2Vent wax motor electrical problem F10E3Drying fan error F1E1Control detected K400 pilot relay stuck closed.F1E2Damaged or corrupted memory on control board; incompatible software components…F2E1Control detected stuck key(s) in keypad or keypad connection.F2E2User interface cannot communicate with main control; loose user interface…F3E1Open connection or component in temperature sensing circuit; open or faulty…F3E2Shorted connection or component in temperature sensing circuit; incoming water…F3E3OWI calibration failure.F4E4Wash motor failure due to loose connection in wash motor circuit and/or open…F5E1Door was not latched within 3 seconds of pressing Start/Resume, or loose…F5E2Control suspects door switch is stuck closed; control programmed to not start…F6E1Low or no water (mechanical problem)F6E2Fill valve electrical problem F6E3Suds/air in pump F6E4Float switch open F6E6Cool water F7E1No heat F7E2Heater stuck on F8E1Slow drain F8E4Drain motor electrical problem F9E1Diverter can't find position F9E2Diverter stuck on F9E3Diverter disc missing F9E4Lower spray arm error

Service modes (6)

Clear Customer Error HistoryDuring Service Diagnostic Cycle Interval 4, press HI TEMP key to clear customer error history.
Error Code Display (within Service Diagnostics)After entering Service Diagnostics Cycle, errors are displayed in intervals 25-22. Interval 27
Rapid Advance ModeAfter starting a cycle, press HI TEMP
Rapid Advance Mode (during normal cycle)Press HI TEMP
Service Diagnostic CycleWith dishwasher in standby mode, press any 3 keys in the sequence 1-2-3, 1-2-3, 1-2-3 with no more…
Service Diagnostics Cycle1

Full entry steps, exit procedures, and test sequences are available in Max.

Related KitchenAid dishwasher models

78,000+ service manuals · 160,000+ error codes · 55+ brands

$29/month · Cancel anytime · Or $9.95 3-day pass