mypros+
Model reference

Maytag MVW18MNAWW0

Washer

5 documents23 error codes10 service modes

Available documentation

Tech Sheet

  • techsheet w10554748 revd40 pg
    Covers this model
  • W10554748 Whirlpool Washer Tech Sheet40 pg
    Covers this model
  • Maytag Washer MVW18PDAWW0 W10554748 Tech Sheet40 pg
    Covers this model

Tech Tip

  • Instruction Sheet2 pg
    Covers this model

Installation Guide

  • Instrucciones de instalacion18 pg
    Covers this model
MyPros+ Max

Diagnose your Maytag MVW18MNAWW0.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (23)

CodeMeaning
F0E0No fault detected.F0E2Over suds condition detected; suds prevent basket from spinning up to speed or…F0E4High water temperature (105°F or higher) detected during rinse cycle.F0E5Off balance load detected.F1E1Main control fault; puts washer out of service.F1E2Motor control fault on the motor control section of the main control.F2E1Stuck key; one or more keys on the User Interface were actuated for 15…F2E3Mismatch of main control and UI; the User Interface identification does not…F3E1Pressure sensor fault; main control detects an out of range pressure signal.F3E2Inlet water temperature fault; inlet thermistor detected to be open or shorted.F5E1Lid switch fault; lid is in locked state but lid switch is open.F5E2Lid lock fault; lid lock has not moved into locked position or motor cannot be…F5E3Lid unlock fault; lid lock has not moved into unlocked position or motor cannot…F5E4Lid not opened between cycles; user presses START after several consecutive…F7E1Basket speed sensor fault; main control cannot determine speed of basket or…F7E5Shifter fault; main control cannot determine position of shifterF7E6Motor fault; indicates an open clockwise or counterclockwise circuit of the…F7E7Motor unable to reach target RPM; basket speed sensor detects that target RPM…F8E1Long fill; water level does not change for a period of time or water is present…F8E3Overflow condition; main control senses water level that exceeds the washer's…F8E5Hot and cold inlet hoses are reversed.F8E6No fill; water level does not change for a period of time or water is present…F9E1Long drain; water level does not change after drain pump is on for 10 minutes.

Service modes (10)

  • Calibration Mode["Enter Service Diagnostic Test Modes.","Toggle cycle selector knob until Rinse LED is ON.","Press…
  • Clean Washer Cycle["Enter Service Diagnostic Test Modes.","Toggle cycle selector knob until Sensing Load, Soak/Wash…
  • Fault Code Display Mode["Enter Service Diagnostic Test Modes.","Toggle cycle selector knob until Done LED is ON (all…
  • Manual Overview Test Mode["Enter Service Diagnostic Test Modes.","Toggle cycle selector knob until Final Spin and Done LEDs…
  • Quick Overview Test Mode["Enter Service Diagnostic Test Modes.","Toggle cycle selector knob until Final Spin LED is…
  • Service Diagnostic Test Mode Entry["Ensure washer is in standby mode (plugged in with all indicators off, or all indicators lit but…
  • Service Diagnostic Test Modes (Entry)["Ensure washer is in standby mode (plugged in with all indicators off, or all indicators lit but…
  • Software Version Display Mode["Enter Service Diagnostic Test Modes.","Toggle cycle selector knob until Rinse, Final Spin, and…
  • Tachometer Verification Mode["Enter Service Diagnostic Test Modes.","Toggle cycle selector knob until Soak/Wash and Done LEDs…
  • UI Test Mode["Enter Service Diagnostic Test Modes.","Toggle cycle selector knob until Rinse and Final Spin LEDs…

Full entry steps, exit procedures, and test sequences are available in Max.

Related Maytag washer models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass