mypros+
Model reference

Maytag MVW18PRBWW0

Washer

3 documents22 error codes21 service modes

Available documentation

Tech Sheet

  • Tech Sheet - W10714946 - Rev C48 pg
    Covers this model

Quick Reference

  • Quick Reference Manual4 pg
    Covers this model

Installation Guide

  • Instrucciones de instalacion18 pg
    Covers this model
MyPros+ Max

Diagnose your Maytag MVW18PRBWW0.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (22)

CodeMeaning
d13Coin 2 sensor is detected as blockedd16Gen 2 debit card reader errord5Coin 1 sensor is detected as blockedd9Low voltageF01Main control fault.F03Pressure sensor faultF07Shifter system failureF11Motor control faultF20Long fillF21Long drainF22Lid lock faultF24Inlet water temperature faultF25Basket speed sensor faultF26Lid switch faultF27Overflow conditionF29Lid unlock faultF32No fillF70Communication failure between CCU and UIF71Communication failure between CCU and UIF73UI EEPROM not programmed or corruptedF74UI EEPROM not programmed or corruptedF77Off balance load detected.

Service modes (21)

  • Calibration Cycle (P-05)["Perform steps 1, 2, and 3 of Activating the Service Diagnostic Test Modes.","Perform step 4 until…
  • Clean Washer Cycle (P-12)["Perform steps 1, 2, and 3 of Activating the Service Diagnostic Test Modes.","Perform step 4 until…
  • Clear Errors (P-01)["Perform steps 1, 2, and 3 of Activating the Service Diagnostic Test Modes.","Press START after…
  • Drain & Spin Cycle (P-06)["Perform steps 1 and 2 of Activating the Service Diagnostic Test Modes.","Perform step 4 until…
  • Help Mode["Perform step 1 of Activating the Service Diagnostic Test Modes.","Perform step 4 until the 2.xx…
  • Manual Overview Test (P-04)["Perform steps 1, 2, and 3 of Activating the Service Diagnostic Test Modes.","Perform step 4 until…
  • P-01 Clear Errors["Perform steps 1, 2, and 3 of Activating the Service Diagnostic Test Modes.","Press START after…
  • P-02 Cycle Credit["Perform steps 1, 2, and 3 of Activating the Service Diagnostic Test Modes.","Perform step 4 until…
  • P-03 Quick Overview Test["Perform steps 1, 2, and 3 of Activating the Service Diagnostic Test Modes.","Perform step 4 until…
  • P-04 Manual Overview Test["Perform steps 1, 2, and 3 of Activating the Service Diagnostic Test Modes.","Perform step 4 until…
  • P-05 Calibration Cycle["Perform steps 1, 2, and 3 of Activating the Service Diagnostic Test Modes.","Perform step 4 until…
  • P-06 Drain & Spin Cycle["Perform steps 1 and 2 of Activating the Service Diagnostic Test Modes.","Perform step 4 until…
  • P-07 UI Diagnostics["Perform steps 1, 2, and 3 of Activating the Service Diagnostic Test Modes.","Perform step 4 until…
  • P-09 Tachometer Verification["Perform steps 1, 2, and 3 of Activating the Service Diagnostic Test Modes.","Perform step 4 until…
  • P-12 Clean Washer Cycle["Perform steps 1, 2, and 3 of Activating the Service Diagnostic Test Modes.","Perform step 4 until…
  • Quick Overview Test (P-03)["Perform steps 1, 2, and 3 of Activating the Service Diagnostic Test Modes.","Perform step 4 until…
  • Service Diagnostic Test Modes["1
  • Service Diagnostic Test Modes (entry)["1
  • Tachometer Verification (P-09)["Perform steps 1, 2, and 3 of Activating the Service Diagnostic Test Modes.","Perform step 4 until…
  • Technician Service Access Code (free vend models only)["Only available on washers set to free vend (6 00).","Press the LEFT UPPER, RIGHT LOWER, RIGHT…
  • UI Diagnostics (P-07)["Perform steps 1, 2, and 3 of Activating the Service Diagnostic Test Modes.","Perform step 4 until…

Full entry steps, exit procedures, and test sequences are available in Max.

Related Maytag washer models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass