mypros+
Model reference

Maytag MVW5430MW1

Washer

7 documents34 error codes10 service modes

Available documentation

Service Manual

  • Dimension Guide12 pg
    Covers this model
  • TECHNICAL MANUAL Maytag® Top Load Washer153 pg
    Covers this model

Tech Sheet

  • tech sheet w11467155 revb2 pg
    Covers this model

Service Flash

  • Technical Service Pointer - Grinding Noise in Spin Cycle3 pg
    Covers this model
  • Technical Service Pointer #W11750573 Rev. B - Vertical Drain Pump Not Draining8 pg
    Covers this model
  • Technical Service Pointer12 pg
    Covers this model

Quick Reference

  • Quick Start Guide2 pg
    Covers this model
MyPros+ Max

Diagnose your Maytag MVW5430MW1.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (34)

CodeMeaning
F0E2Wrong voltage detected.F0E3Long drain faultF0E4Water hazard condition detected.F0E5Overflow or flood condition detected.F0E7Long fillF0E8Motor drive module over current or overload condition.F0E9Motor phase loss detected.F1E1Locked rotorF1E2Motor drive module over temperature condition.F2E1Motor unable to reach target RPM.F2E2Motor circuit open.F2E3Basket re-engagement failure.F3E2Basket engaged during wash.F3E3MCI drive failure.F5E1Tachometer missing or wrong signal.F5E3Communication errorF5E4Communication errorF6E1Lid not opened between cycles.F6E3Lid will not lock or unlock.F7E1Lid switch faultF7E2Inlet water temperature fault.F7E3Pressure system fault.F7E4ACU/UI mismatchF7E6UI disconnected from main control.F7E7UI stuck button detected.F7E8Motor drive module over voltage.F7E9Main control (ACU) fault.F7EAOff balance pause condition detected.F7ECWater ring detected.F8E1Load detected when running Clean Washer cycle.
View all 34 error codes
F8E3Off balance load detected.F8E6Spin limited by water temperature.F9E1Overload condition detected.F9E9Oversuds condition detected.

Service modes (10)

  • Automatic Test["From Service Mode, rotate E3 in clockwise direction until LED2 is ON.","Press Start key."]
  • Automatic Test Mode["Enter Service Diagnostic Mode first.","Rotate encoder 3 until LED2 is ON.","Press SW2/Start key…
  • Factory Calibration Cycle["Ensure washer is in standby mode (plugged in with all LEDs off) and lid is closed.","Within 8…
  • Fault History["From Service Mode, rotate E3 in clockwise direction until LED1 is ON.","Press Start key."]
  • Fault History Display["Enter Service Diagnostic Mode first.","Rotate encoder 3 until LED1 is ON.","Press SW2/Start…
  • Service Diagnostic Mode["Ensure washer is in standby mode (plugged in with all LEDs off).","Using encoder E3 (cycle…
  • Service Mode Entry["Ensure washer is in standby mode (plugged in with all LEDs off).","Ensure product is in OFF…
  • Software Version["From Service Mode, rotate E3 in clockwise direction until LED4 is ON.","Press Start key."]
  • Software Version Display["Enter Service Diagnostic Mode first.","Rotate encoder 3 until LED4 turns ON.","Press SW2/Start…
  • UI Test["From Service Mode, rotate E3 in clockwise direction until LED3 is ON.","Press Start key."]

Full entry steps, exit procedures, and test sequences are available in Max.

Related Maytag washer models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass