mypros+
Model reference

Maytag MVW6230HC2

Washer

13 documents35 error codes10 service modes

Available documentation

Service Manual

  • Dimension Guide12 pg
    Covers this model
  • Whirlpool® and Maytag® 4.7/5.3 Cubic Foot Top Load Washer Technical Manual88 pg
    Covers this model
  • Technical Manual - Whirlpool® and Maytag® 4.7/5.3 Cubic Foot Top Load Washer88 pg
    Covers this model

Tech Sheet

  • Tech Sheet W11423870A2 pg
    Covers this model
  • Tech Sheet - W11580994 - Rev B2 pg
    Covers this model
  • MVW6230HC tech sheet70 pg
    Covers this model

Service Flash

  • Service Pointer - W11681398 - Rev A - Maytag Top Load Washers Over the Air Update Error3 pg
    Covers this model
  • Service Pointer - W11617330 - Rev A - Top Load Washers Out-of-Balance Condition Notifications8 pg
    Covers this model
  • Technical Service Pointer - Grinding Noise in Spin Cycle3 pg
    Covers this model
  • Service Pointer - W11632927 - Rev I - Top Load Washer Will Not Run Cycle and/or GFCI Ground Fault Failure9 pg
    Covers this model
  • Technical Service Pointer #W11750573 Rev. B - Vertical Drain Pump Not Draining8 pg
    Covers this model
  • Technical Service Pointer12 pg
    Covers this model

Quick Reference

  • Quick Reference Guide24 pg
    Covers this model
MyPros+ Max

Diagnose your Maytag MVW6230HC2.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (35)

CodeMeaning
F0E2Oversuds condition detected during wash cycle.F0E3Overload condition detected.F0E4Spin limited by water temperature.F0E5Off balance load detected.F0E7Load detected when running Clean Washer cycle.F0E8Water ring condition detected.F0E9Off balance pause condition.F1E1Main Control (ACU) fault.F1E2Motor drive module over voltage.F2E1UI stuck button detected.F2E2UI (User Interface) disconnected.F3E2Pressure system fault.F3E3Inlet water temperature fault.F3E5Mini Bulk system error.F5E1Lid switch faultF5E2Lid lock will not unlock; excessive force on lid, wash media buildup, or main…F5E3Lid will not lock or unlock.F5E4Lid not opened between cycles.F6E1Communication errorF6E3Communication errorF7E1Tachometer missing or wrong signal.F7E2MCI drive failure.F7E3Basket engaged during wash.F7E4Basket re-engagement failure.F7E6Motor circuit open.F7E7Motor unable to reach target RPM.F7E8Motor drive module over temperature.F7E9Locked rotor condition.F7EAMotor phase lost.F7ECMotor drive module over current/overload.
View all 35 error codes
F8E1Long fillF8E2Dispenser system failure.F8E3Overflow or flood condition detected.F8E6Water hazard condition detected.F9E1Long drain fault

Service modes (10)

  • Component Activation["Enter Service Mode.","Navigate to Service Diagnostics.","Select Component Activation."]
  • Component Activation Mode["Enter Service Mode.","Navigate to Service Diagnostics.","Select Component Activation.","Use…
  • Demo Mode["Enter Service Mode.","Navigate to DEMO MODE.","Toggle On or Off."]
  • Diagnostic Cycle["Enter Service Mode.","Navigate to Service Diagnostics.","Select Diagnostic Cycle."]
  • DLMS Calibration Cycle["Enter Service Mode.","Navigate to Factory Diagnostics.","Select DLMS Calibration Cycle."]
  • Fault History["Enter Service Mode.","Navigate to Fault History."]
  • HMI Test["Enter Service Mode.","Navigate to Service Diagnostics.","Select HMI Test."]
  • Sensor Feedback["Enter Service Mode.","Navigate to Service Diagnostics.","Select Sensor Feedback."]
  • Sensor Feedback Mode["Enter Service Mode.","Navigate to Service Diagnostics.","Select Sensor Feedback.","Use Left/Right…
  • Service Mode["Ensure the washer is in standby mode (plugged in with all indicators off).","Select any three (3)…

Full entry steps, exit procedures, and test sequences are available in Max.

Related Maytag washer models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass