mypros+
Model reference

Maytag MVW6200KW2

Washer

14 documents34 error codes10 service modes

Available documentation

Tech Sheet

  • Service Technical Sheet W11416398B2 pg
    Covers this model
  • MVW6200KW tech sheet w11416395 reva132 pg
    Covers this model

Service Manual

  • TECHNICAL MANUAL Maytag® 4.8 Cubic Foot Top Load Washer132 pg
    Covers this model

Service Flash

  • Service Pointer - W11624962 - Rev D - Top Load Washer Wash Cycle Not Advancing3 pg
    Covers this model
  • Service Pointer - W11618678 - Rev A - Top Load Washers Cycle Won't Start3 pg
    Covers this model
  • Service Pointer - W11617330 - Rev A - Top Load Washers Out-of-Balance Condition Notifications8 pg
    Covers this model
  • Technical Service Pointer - Grinding Noise in Spin Cycle3 pg
    Covers this model
  • Service Pointer - W11632927 - Rev I - Top Load Washer Will Not Run Cycle and/or GFCI Ground Fault Failure9 pg
    Covers this model
  • Technical Service Pointer #W11750573 Rev. B - Vertical Drain Pump Not Draining8 pg
    Covers this model
  • Technical Service Pointer12 pg
    Covers this model

Training

  • Training Manual Service Tool31 pg
    Covers this model

Quick Reference

  • Quick Start Guide2 pg
    Covers this model
  • Quick Reference Guide - Service Tool - Rev B2 pg
    Covers this model

Other

  • Wtw5010lw0 owners-manual-w11436596-reva21 pg
    Covers this model
MyPros+ Max

Diagnose your Maytag MVW6200KW2.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (34)

CodeMeaning
F0E2Oversuds condition detectedF0E3Overload detectedF0E4Spin limited by water temperatureF0E5Off balance load condition detected.F0E7Load detected when running Clean Washer cycle.F0E8Too much residual water detected in the tub.F0E9Off balance pauseF1E1Main control (ACU) fault detected.F1E2Motor drive module over voltage.F2E1HMI stuck buttonF2E2HMI disconnected from the ACU.F2E3Locked rotor condition.F3E2Pressure system faultF3E3Inlet water temperature faultF5E1Lid switch faultF5E3Lid lock will not unlockF5E4Lid not opened between cyclesF6E1Communication errorF6E3Communication errorF7E1Tachometer missing or wrong signalF7E2MCI drive failure.F7E3Basket engaged during washF7E4Basket re-engagement failureF7E6Motor circuit openF7E7Motor unable to reach target RPM.F7E8UI stuck button detected.F7E9UI disconnected.F7EAACU/UI mismatch.F7ECMotor drive module over current/overload.F8E1Long fill
View all 34 error codes
F8E3Overflow or flood conditionF8E6Water hazardF9E1Drain pump system problemF9E9Wrong voltage detected at power supply.

Service modes (10)

  • Automatic TestFrom service mode, press Key 2 and then Key 5.
  • Button Activation & Encoder Test["Activate Service Diagnostic Mode first.","Press and release Key 1.","Encoder Test starts…
  • Fault Code Display / History["Activate Service Diagnostic Mode first.","Press and release Key 3 to display most recent fault…
  • Fault HistoryFrom service mode, press Key 3.
  • Service Diagnostic Mode["Ensure washer is in standby mode (plugged in with all LEDs off).","Within 8 seconds, perform the…
  • Service Mode Entry1. Ensure washer is in standby mode (plugged in with all LEDs off). 2. Within 8 seconds
  • Service Test Mode["Activate Service Diagnostic Mode first.","Press and release Key 2.","Press and release the START…
  • Software VersionFrom service mode, press Key 2 for 3 seconds.
  • Software Version Display["Activate Service Diagnostic Mode first.","Press and hold Key 2 for 5 seconds.","Display…
  • UI TestFrom service mode, press Key 1.

Full entry steps, exit procedures, and test sequences are available in Max.

Related Maytag washer models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass