mypros+
Model reference

Maytag MVW4505MW0

Washer

10 documents34 error codes10 service modes

Available documentation

Tech Sheet

  • Tech Sheet W11466159B2 pg
    Covers this model

Service Manual

  • Dimension Guide12 pg
    Covers this model
  • TECHNICAL MANUAL Maytag® Top Load Washer153 pg
    Covers this model

Service Flash

  • Technical Service Pointer - Grinding Noise in Spin Cycle3 pg
    Covers this model
  • Service Pointer - W11632927 - Rev I - Top Load Washer Will Not Run Cycle and/or GFCI Ground Fault Failure9 pg
    Covers this model
  • Technical Service Pointer #W11750573 Rev. B - Vertical Drain Pump Not Draining8 pg
    Covers this model
  • Technical Service Pointer12 pg
    Covers this model

Quick Reference

  • Quick Start Guide2 pg
    Covers this model
  • Manual de referencia rápida1 pg
    Covers this model
  • Quick Start Guide2 pg
    Covers this model
MyPros+ Max

Diagnose your Maytag MVW4505MW0.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (34)

CodeMeaning
F0E2Oversuds condition detected.F0E3Overload condition detected.F0E4Spin limited by water temperature.F0E5Off balance load detected.F0E7Load detected when running Clean Washer cycle.F0E8Water ring condition.F0E9Off balance pause.F1E1Main Control (ACU) fault.F1E2Motor drive module over voltage.F2E1UI stuck button.F2E2UI disconnected.F2E3ACU/UI mismatch.F3E2Pressure system fault.F3E3Inlet water temperature fault.F5E1Lid switch faultF5E3Lid will not lock or unlock.F5E4Lid not opened between cycles.F6E1Communication errorF6E3Communication errorF7E1Tachometer missing or wrong signal.F7E2MCI drive failure.F7E3Basket engaged during wash.F7E4Basket re-engagement failure.F7E6Motor circuit open.F7E7Motor unable to reach target RPM.F7E8Motor drive module over temperature.F7E9Locked rotor.F7EAMotor phase loss.F7ECMotor drive module over current/overload.F8E1Long fill condition.
View all 34 error codes
F8E3Overflow or flood condition.F8E6Water hazard.F9E1Long drain fault.F9E9Wrong voltage.

Service modes (10)

  • Automatic TestFrom Service Mode
  • Automatic Test Mode["Enter Service Diagnostic Mode first.","Rotate encoder 3 until LED2 is ON.","Press SW2/Start key…
  • Factory Calibration Cycle["Ensure washer is in standby mode (plugged in with all LEDs off) and lid is closed.","Within 8…
  • Fault HistoryFrom Service Mode
  • Fault History Display["Enter Service Diagnostic Mode first.","Rotate encoder 3 until LED1 is ON.","Press SW2/Start…
  • Service Diagnostic Mode["Ensure washer is in standby mode (plugged in with all LEDs off).","Using encoder E3 (cycle…
  • Service Mode Entry1. Ensure washer is in standby mode (plugged in with all LEDs off). 2. Using E3 cycle selection…
  • Software VersionFrom Service Mode
  • Software Version Display["Enter Service Diagnostic Mode first.","Rotate encoder 3 until LED4 turns ON.","Press SW2/Start…
  • UI TestFrom Service Mode

Full entry steps, exit procedures, and test sequences are available in Max.

Related Maytag washer models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass