mypros+
Model reference

Maytag MVW18PDAWW0

Washer

3 documents44 error codes18 service modes

Available documentation

Tech Sheet

  • Maytag Washer MVW18PDAWW0 W10554748 Tech Sheet40 pg
    Covers this model
  • Tech Sheet - W10554751 - Rev B48 pg
    Covers this model

Installation Guide

  • Instrucciones de instalacion18 pg
    Covers this model
MyPros+ Max

Diagnose your Maytag MVW18PDAWW0.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (44)

CodeMeaning
d13Coin 2 failured16Gen 2 debit card reader errord5Coin 1 blocked/failured9Low voltageF01Main control fault.F03Pressure sensor/switch faultF07Shifter system failureF0E2Over suds condition detected; suds prevent basket from spinning up to speed or…F0E4High water temperature (105°F or higher) detected during rinse cycle.F0E5Off balance load detected.F11Motor control faultF1E1Main control fault; puts washer out of service.F1E2Motor control fault on the motor control section of the main control.F20Long fillF21Long drainF22Lid lock faultF24Inlet water temperature faultF25Basket speed sensor faultF26Lid switch faultF27Overflow conditionF29Lid unlock faultF2E1Stuck key; one or more keys on the User Interface were actuated for 15…F2E3Mismatch of Main Control and User Interface; UI identification does not match…F32No fillF3E1Pressure sensor fault; main control detects an out of range pressure signal.F3E2Inlet water temperature fault; inlet thermistor detected as open or shorted.F5E1Lid switch fault; lid is in locked state but lid switch is open.F5E2Lid lock fault; lid lock has not moved into locked position or motor cannot be…F5E3Lid unlock fault; lid lock has not moved into unlocked position or motor cannot…F5E4Lid not opened between cycles; user presses START after several consecutive…
View all 44 error codes
F70Communication failure between CCU and UIF71Communication failure between CCU and UIF73UI EEPROM not programmed or corruptedF74UI EEPROM not programmed or corruptedF77Off balance load detected.F7E1Basket speed sensor fault; main control cannot determine speed of basket or…F7E5Shifter fault; main control cannot determine position of shifterF7E6Motor fault; indicates an open clockwise or counterclockwise circuit of the…F7E7Motor unable to reach target RPM; basket speed sensor detects that target RPM…F8E1Long fill; water level does not change for a period of time or water is present…F8E3Overflow condition; main control senses water level that exceeds the washer's…F8E5Hot and cold inlet hoses are reversed.F8E6No fill; water level does not change for a period of time or water is present…F9E1Long drain; water level does not change after drain pump is on for 10 minutes.

Service modes (18)

  • Calibration Mode["Enter Service Diagnostic Test Modes.","Toggle cycle selector knob until 'Rinse' LED is…
  • Clean Washer Cycle["Enter Service Diagnostic Test Modes.","Toggle cycle selector knob until 'Sensing Load'…
  • Fault Code Display Mode["Enter Service Diagnostic Test Modes.","Toggle cycle selector knob until 'Done' LED is ON (all…
  • Help Mode["Perform step 1 of Activating the Service Diagnostic Test Modes.","Perform step 4 until the 2.xx…
  • Manual Overview Test Mode["Enter Service Diagnostic Test Modes.","Toggle cycle selector knob until 'Final Spin' and 'Done'…
  • P-01 Clear Errors["Perform steps 1, 2, and 3 of Activating the Service Diagnostic Test Modes.","Press START after…
  • P-03 Service Diagnostic["Perform steps 1, 2, and 3 of Activating the Service Diagnostic Test Modes.","Perform step 4 until…
  • P-04 Manual Diagnostic["Perform steps 1, 2, and 3 of Activating the Service Diagnostic Test Modes.","Perform step 4 until…
  • P-05 Calibration Cycle["Perform steps 1, 2, and 3 of Activating the Service Diagnostic Test Modes.","Perform step 4 until…
  • P-07 UI Diagnostics["Perform steps 1, 2, and 3 of Activating the Service Diagnostic Test Modes.","Perform step 4 until…
  • P-09 Tachometer Verification["Perform steps 1, 2, and 3 of Activating the Service Diagnostic Test Modes.","Perform step 4 until…
  • P-12 Clean Washer Cycle["Perform steps 1, 2, and 3 of Activating the Service Diagnostic Test Modes.","Perform step 4 until…
  • Quick Overview Test Mode["Enter Service Diagnostic Test Modes.","Toggle cycle selector knob until 'Final Spin' LED is…
  • Service Diagnostic Test Modes (entry)["1
  • Software Version Display Mode["Enter Service Diagnostic Test Modes.","Toggle cycle selector knob until 'Rinse', 'Final Spin'…
  • Tachometer Verification Mode["Enter Service Diagnostic Test Modes.","Toggle cycle selector knob until 'Soak/Wash' and 'Done'…
  • Technician Service Access Code (free vend models only)["Only available on washers set to free vend (6 00).","Press the LEFT UPPER, RIGHT LOWER, RIGHT…
  • UI Test Mode["Enter Service Diagnostic Test Modes.","Toggle cycle selector knob until 'Rinse' and 'Final Spin'…

Full entry steps, exit procedures, and test sequences are available in Max.

Related Maytag washer models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass