mypros+
Model reference

Maytag MVW18PDAGW0

Washer

4 documents43 error codes18 service modes

Available documentation

Tech Sheet

  • Tech Sheet - W10554757 - Rev C24 pg
    Covers this model
  • Techsheet W10468342 RevC44 pg
    Covers this model

Tech Tip

  • Instruction Sheet2 pg
    Covers this model

Installation Guide

  • Installation Instructions76 pg
    Covers this model
MyPros+ Max

Diagnose your Maytag MVW18PDAGW0.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (43)

CodeMeaning
d13The Coin 2 sensor is detected as blocked; coin vault may be full of money, or…d16Gen 2 Debit Card Reader Errord5The Coin 1 sensor is detected as blocked; coin vault may be full of money, or…d9Low voltageF01Indicates a main control fault.F03Main control detects an out of range pressure signal from the pressure…F07Main control cannot determine position of shifter (shifter system failure).F0E2Over suds condition detected; suds prevent basket from spinning up to speed or…F0E4High water temperature detected during rinse cycle (105°F or higher).F0E5Off balance load detected.F11Motor control faultF1E1Main control fault.F1E2Motor control fault; fault of the motor control section of the main control.F20Long fillF21Long drainF22Lid lock faultF24Inlet water temperature faultF25Basket speed sensor faultF26Lid switch faultF27Overflow conditionF29Lid unlock faultF2E1Stuck key; one or more keys on the User Interface were actuated for 15…F2E3Mismatch of main control and UI; User Interface identification does not match…F32No fillF3E1Pressure system fault; main control detects an out of range pressure signal.F3E2Inlet water temperature fault; inlet thermistor detected to be open or shorted.F5E1Lid switch faultF5E2Lid lock fault; lid lock has not moved into locked position or motor cannot be…F5E3Lid unlock fault; lid lock has not moved into unlocked position or motor cannot…F5E4Lid not opened between cycles; user presses START after several consecutive…
View all 43 error codes
F70Communication failure between CCU and UIF71Communication failure between CCU and UIF73The User Interface EEPROM identification does not match the expected value in…F74The User Interface EEPROM identification does not match the expected value in…F77Off balance load detected.F7E1Basket speed fault; main control cannot determine speed of basket or speed…F7E5Shifter fault; main control cannot determine position of shifter.F7E6Motor fault; indicates an open clockwise or counterclockwise circuit of the…F7E7Motor unable to reach target RPM; basket speed sensor detects that target RPM…F8E1No fill, long fill; water level does not change for a period of time or water…F8E3Overflow condition; main control senses water level that exceeds the washer's…F8E5Hot and cold inlet hoses are reversed.F9E1Long drain; water level does not change after the drain pump is on for 10…

Service modes (18)

  • Automatic Test Mode["Enter Service Diagnostic Test Modes.","Turn cycle selector knob until 'Spin' LED is On (or '02'…
  • Calibration Mode["Enter Service Diagnostic Test Modes.","Turn cycle selector knob until 'Rinse' LED is On (or '04'…
  • Fault Code Display Mode["Enter Service Diagnostic Test Modes.","Turn cycle selector knob until 'Done' LED is On (or '01'…
  • Help Mode["1
  • Manual Test Mode["Enter Service Diagnostic Test Modes.","Turn cycle selector knob until 'Spin & Done' LEDs are On…
  • P-01 Clear Errors["Access Service Diagnostic Test Modes.","Press START after 'P-01' is displayed to clear an active…
  • P-02 Cycle Credit["Access Service Diagnostic Test Modes.","Press Normal key pad to step to 'P-02'.","Press START…
  • P-03 Service Diagnostic["Access Service Diagnostic Test Modes.","Press Normal key pad to step to 'P-03'.","Press START…
  • P-04 Manual Diagnostic["Access Service Diagnostic Test Modes.","Press Normal key pad to step to 'P-04'.","Press START…
  • P-05 Calibration Cycle["Access Service Diagnostic Test Modes.","Press Normal key pad to step to 'P-05'.","Press START…
  • P-07 UI Diagnostics["Access Service Diagnostic Test Modes.","Press Normal key pad to step to 'P-07'.","Press START…
  • P-09 Tachometer Verification["Access Service Diagnostic Test Modes.","Press Normal key pad to step to 'P-09'.","Press START…
  • P-12 Clean Washer Cycle["Access Service Diagnostic Test Modes.","Press Normal key pad to step to 'P-12'.","Press START…
  • Service Diagnostic Test Modes (entry)["1
  • Software Version Display Mode["Enter Service Diagnostic Test Modes.","Turn cycle selector knob until 'Rinse, Spin, and Done'…
  • Tachometer Verification Mode["Enter Service Diagnostic Test Modes.","Turn cycle selector knob until 'Wash and Done' LEDs are On…
  • Technician Service Access Code (free vend models only)["This method is only available on washers set to free vend (6 00).","Press the LEFT UPPER, RIGHT…
  • UI Test Mode["Enter Service Diagnostic Test Modes.","Turn cycle selector knob until 'Rinse & Spin' LEDs are On…

Full entry steps, exit procedures, and test sequences are available in Max.

Related Maytag washer models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass