Model reference

Whirlpool SF367LXSS0

Range

16 documents35 error codes6 service modes

Available documentation

Tech Sheet

Tech Sheet - W10041630 - Rev A (FR)8 pg
Covers this model
Tech Sheet - 9762973 - Rev A6 pg
Covers this model
Whirlpool Range SF362LXSB0 Tech Sheet6 pg
Covers this model
Whirlpool Range SF362LXST0 Tech Sheet6 pg
Covers this model

Service Manual

Whirlpool Gas Range Direct Spark Ignition System29 pg
Covers this model
Job Aid - 30″ Freestanding Self-Cleaning Gas Range68 pg
Covers this model
30″ Freestanding Self-Cleaning Gas Range68 pg
Covers this model
Whirlpool Gas Range Direct Spark Ignition System KR-2829 pg
Covers this model

Service Flash

Service Pointer - Door Glass Slipping/Falling1 pg
Covers this model
Service Pointer - 8178185 - Rev A Ignition Problems2 pg
Covers this model
Service Pointer - 8178446 - PF Error Code Appears All the Time2 pg
Covers this model

Installation Guide

Installation Instructions32 pg
Covers this model
Instruction Sheet2 pg
Covers this model
Instruction Sheet2 pg
Covers this model

Other

Service Pointer - 8178622 - Glass Slipping From Door FRAME_81786221 pg
Covers this model
81781852 pg
Covers this model

MyPros+ Max

Diagnose your Whirlpool SF367LXSS0.

Step-by-step diagnostics from the service manual
Test values, resistance specs, and wiring references
Verified part numbers when replacement is needed

Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

M+

M+ Max·Whirlpool Range

E0 on my Whirlpool SF367LXSS0

M+

EEPROM communication failure, possibly

From Tech Sheet W12665424, p.36:

1.Access service mode to confirm the active fault code and read stored error history.

2.Measure control board supply voltage at test points. Expected: 12 VDC and 5 VDC.

3.Inspect all connectors on the main control for corrosion or backed-out pins.

Part WPW10804018

Electronic control board

Error codes (35)

CodeMeaning

E0EEPROM communication failure, possibly caused by power line noise or lightning.E1EEPROM checksum failure, possibly caused by power line noise or lightning.E2Short circuit in oven sensor circuit E3Door latch malfunction F0 E0Factory default F1 E0EEPROM checksum failure.F1 E1EEPROM communications error.F1 E2UL A/D error(s).F1 E4Model ID error.F1 E6Latch signal mismatch error.F1-E0EEPROM communications / EEPROM checksum failure.F1-E1EEPROM checksum failure.F1-E2UL A/D error(s).F2 E0Shorted key detected.F2 E1Key tail unplugged.F3 E0Oven sensor opened.F3 E1Oven sensor shorted.F3 E2BAKE/BROIL range over temperature.F3 E3CLEAN range over temperature.F3 E4Oven sensor opened F3 E5Oven sensor shorted F3 E6Warming drawer sensor open.F3 E7Warming drawer sensor shorted.F3-E0Oven sensor opened (open circuit in oven temperature sensor).F3-E1Oven sensor shorted.F3-E2BAKE/BROIL range over temperature condition.F3-E3CLEAN range over temperature condition.F5 E0Door and switches do not agree.F5 E1Door latch not operating.F5 E2Latch error during CLEAN.

View all 35 error codes

F5-E0Door and switches do not agree (door switch mismatch).F5-E1Door latch not operating.F5-E2Latch error during CLEAN cycle.F8 E0N/A (no likely failure condition described).PFA reset has occurred in the Electronic Range Control (ERC), typically caused by…

Service modes (6)

Diagnostics ModeWith oven not in cooking, broiling, or cleaning mode, press Cancel/OFF, Cancel/OFF, START. The…
Last Error Code RecallPress and hold the CANCEL/OFF key for 5 seconds until the last error code is displayed.
Manual Diagnostic Mode 1Enter within 120 seconds of power-up
Manual Diagnostic Mode 2Enter more than 120 seconds after power-up
Temperature Adjustment ModePress and hold BAKE key for 5 seconds
Temperature Calibration (Touchpad control module)Press and hold BAKE for 5 seconds

Full entry steps, exit procedures, and test sequences are available in Max.

Related Whirlpool range models

78,000+ service manuals · 160,000+ error codes · 55+ brands

$29/month · Cancel anytime · Or $9.95 3-day pass