mypros+
Model reference

Whirlpool YGFE461LVQ0

Range

9 documents27 error codes22 service modes

Available documentation

Tech Sheet

  • Tech Sheet - W10198612 - Rev B (FR)6 pg
    Covers this model
  • Tech Sheet6 pg
    Covers this model
  • Tech Sheet - W10435365 - Rev A8 pg
    Covers this model
  • Tech Sheet - W10435366 - Rev A (FR)8 pg
    Covers this model

Service Manual

  • Troubleshooting Gas and Electric Freestanding Range Electronic Controls70 pg
    Covers this model

Service Flash

  • Technical Service Pointer - W10412840 (Passive Door Hinge Design)6 pg
    Covers this model
  • Technical Education Service Update Second Half — 201172 pg
    Covers this model

Installation Guide

  • Installation Instructions16 pg
    Covers this model
  • Instruction Sheet2 pg
    Covers this model
MyPros+ Max

Diagnose your Whirlpool YGFE461LVQ0.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (27)

CodeMeaning
F1Control failure or UL A/D error(s) detected in the control board.F1 E*Control board failure (all F1 sub-codes indicate control fault).F1-E0EEPROM communication error.F1-E5Sensor out of range.F1-E7PCB thermistor open or shorted.F1-E9Cancel key error code.F2Shorted/stuck key detected on the control keypad.F2-E0Keypad disconnected.F2-E1Stuck key.F2-E2Cancel key error.F3Oven sensor opened or oven sensor shorted.F3 E0Oven temperature sensor fault (open or shorted)F3 E1Lower oven temperature sensor fault (MRC II double oven models).F3 E2Warming drawer temperature sensor fault.F3-E0Main oven sensor open or shorted.F3-E2Warming drawer sensor open or shorted.F5 E0Door position switch faultF5 E1Door latch switch/system faultF5 E2Door switch fault.F5-E0Door and switches do not agree (Clean mode).F5-E1Door latch not operating (Clean mode).F6 E*Control communication failure.F6-E0No communication (connection failure).F6-E1Over temperature during cook mode.F6-E2Over temperature during clean mode.F6-E3Over temperature (warming drawer).F9House miswired

Service modes (22)

  • Auto TestEnter diagnostic mode (CANCEL > CANCEL > START), then use up arrow or '+' to scroll to AUTO TEST
  • CONTROL RESETPress CANCEL > CANCEL > START to enter Service Mode
  • diagnosticWith the oven not in bake, broil, or clean mode, press CANCEL/OFF, CANCEL/OFF, START in that order
  • Diagnostics Mode (Auto Test)Press CANCEL > CANCEL > START
  • DISPLAYPress CANCEL > CANCEL > START to enter Service Mode
  • ENG MODEPress CANCEL > CANCEL > START to enter Service Mode
  • ENG MODE (Engineering Mode)Enter diagnostic mode, scroll to step 2 (ENG MODE)
  • FAULTSPress CANCEL > CANCEL > START to enter Service Mode
  • LCC Diagnostic Mode (LCC90/LCC95/LCC180)["Press CANCEL, CANCEL, START in sequence.","Press TEMP/TIME '+' key to cycle through diagnostic…
  • LCC190 Diagnostic Mode (Self Clean, Convection models)["Press CANCEL, CANCEL, START in sequence.","Press TEMP/TIME or TEMP/HOUR '+' key to cycle through…
  • MRC Control Module Diagnostic ModePress CANCEL > CANCEL > START
  • MRC Diagnostic Mode["Press CANCEL, CANCEL, START in sequence.","Press TEMP/TIME '+' key to cycle through diagnostic…
  • MRC Diagnostic Mode (Fan/True Convection Electric - Oven Light entry)["Press CANCEL, CANCEL, START in sequence.","Press TEMP/TIME '+' key to cycle through diagnostic…
  • MRC II Diagnostic Mode (Number 3 key entry - KitchenAid models)["Press OFF/OFF/START or CANCEL/CANCEL/START in sequence.","Press the number '3' key to cycle…
  • MRC II Diagnostic Mode (TEMP/TIME entry)["Press CANCEL, CANCEL, START in sequence.","Press TEMP/TIME '+' keypad to cycle through diagnostic…
  • Temperature AdjustmentPress OVEN LIGHT for 5 seconds (current offset or 0° displayed)
  • Temperature Calibration AdjustmentPress and hold OVEN LIGHT for 5 seconds. Current offset value is displayed (or 0° if none set). Use…
  • TEST MODEPress CANCEL > CANCEL > START to enter Service Mode
  • TEST ON - Relay ControlEnter diagnostic mode (CANCEL > CANCEL > START)
  • TEST ON (Relay Checks)Press CANCEL > CANCEL > START to enter Service Mode
  • USAGEPress CANCEL > CANCEL > START to enter Service Mode
  • VERSIONPress CANCEL > CANCEL > START to enter Service Mode

Full entry steps, exit procedures, and test sequences are available in Max.

Related Whirlpool range models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass