mypros+
Error code reference

Bosch Dryer Error Code E:2022

Main heating circuit

Bosch codesBosch dryer codes

Main heating circuit - heating element overheating (Error) (4-digit equivalent of E:06).

First step from the service manual

Clean lint filter.

The complete diagnostic procedure includes additional test steps, resistance specifications, wiring diagram references, and component test points.

MyPros+ Max

Get the full diagnostic procedure for E:2022.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What E:2022 means on a Bosch dryer

Error code E:2022 on a Bosch dryer indicates an overheating condition in the main heating circuit, specifically at the heating element. This code is the 4-digit equivalent of the older E:06 designation and is triggered when the dryer's thermal monitoring system detects that the heating element has exceeded its safe operating temperature threshold. The control board receives feedback from thermal sensors or thermostats positioned near the heating assembly and cuts power or flags the fault when temperatures climb beyond acceptable limits.

The heating element overheating condition is almost always caused by restricted airflow through the dryer. When lint accumulates in the filter, exhaust duct, or internal passages, hot air cannot escape efficiently, causing heat to build up around the element itself. The primary and first diagnostic step is to clean the lint filter thoroughly, as a clogged filter is the most frequent trigger for this fault. Beyond the lint filter, the exhaust duct running from the dryer to the exterior vent should be inspected for blockages, kinks, or excessive length that reduces airflow.

If airflow is confirmed to be clear and the error persists, the fault may point to a failing high-limit thermostat, a cycling thermostat out of calibration, or a heating element that is partially shorted and generating excessive heat. A faulty thermal cutoff fuse that has not fully opened can also produce erratic heating behavior. Diagnosing these components requires a multimeter to test continuity and resistance values across each part of the heating circuit to isolate the defective component.

Source: manufacturer service documentation.

Common causes of E:2022

  1. 01

    Clogged lint filter

    Wiring / connection

    A lint-packed filter blocks airflow through the drum, causing heat to accumulate around the heating element. Remove and clean the lint filter completely, then run a test cycle to see if the error clears.

  2. 02

    Blocked or kinked exhaust duct

    Wiring / connection

    A restricted exhaust duct prevents hot air from venting to the outside, allowing temperatures inside the heater assembly to rise beyond safe levels. Inspect the full length of the duct for lint buildup, crushing, or sharp bends.

  3. 03

    Failed high-limit thermostat

    Part replacement

    The high-limit thermostat is designed to interrupt the heating circuit when temperatures become dangerously high, but a thermostat that fails in a closed position will not cut power in time. Test for continuity with a multimeter and replace if the component does not open at its rated temperature.

  4. 04

    Thermal cutoff fuse failure

    Part replacement

    The thermal cutoff fuse is a one-time protection device that opens permanently if the heating circuit overheats. A fuse that has partially failed or one that has blown but is being bypassed can contribute to repeated overheating faults. Check continuity across the fuse and replace it if it reads open.

  5. 05

    Defective heating element

    Part replacement

    A heating element with a partial short to ground can generate more heat than the circuit is designed to handle, triggering the overheating error. Inspect the element for visible damage and test resistance with a multimeter to confirm it is within specification.

See the test procedure for each cause

Frequently asked questions about E:2022

What does E:2022 mean on a Bosch dryer?
E:2022 indicates that the main heating circuit has detected an overheating condition at the heating element. It is the 4-digit version of the older E:06 fault code. The dryer's control board triggers this error when thermal sensors detect temperatures beyond the safe operating range in the heater assembly. Restricted airflow from a dirty lint filter is the most common cause.
How do I fix error code E:2022 on my Bosch dryer?
Start by cleaning the lint filter completely, as this is the most frequent cause of the overheating fault. Next, inspect the exhaust duct from the back of the dryer to the exterior vent for blockages, kinks, or excessive lint buildup. If the error returns after restoring proper airflow, a technician should test the high-limit thermostat, thermal cutoff fuse, and heating element for faults using a multimeter.
Is it safe to keep using my Bosch dryer when E:2022 is displayed?
No, you should not continue operating the dryer while this error is active. An overheating heating element is a potential fire hazard, and the dryer's safety systems are flagging a condition that exceeds normal operating temperatures. Stop using the dryer until the cause of the restricted airflow or component fault has been identified and corrected.
Will resetting the dryer clear the E:2022 error code?
A reset may temporarily clear the error from the display, but the fault will return if the underlying cause has not been fixed. If the lint filter and exhaust duct are clean and the error still comes back, a component in the heating circuit such as the high-limit thermostat or thermal cutoff fuse likely needs to be replaced. Resetting without repairing the root cause does not make the dryer safe to use.
How much does it cost to repair a Bosch dryer showing error E:2022?
If the fix is simply cleaning the lint filter and exhaust duct, there may be no parts cost at all, though a professional duct cleaning service can run anywhere from $80 to $200 depending on duct length and access. If a thermostat, thermal cutoff fuse, or heating element needs replacement, parts and labor typically range from $150 to $400 depending on the specific component and local labor rates. Getting a diagnostic visit from a qualified appliance technician will give you a more accurate estimate for your specific situation.

Related Bosch dryer codes

All Bosch dryer codes
View all 94 Bosch dryer codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass