Skip to main content
Error code reference
Electrolux Air Conditioner Error Codes
49 error codes documented with diagnostic procedures.
Have your model number? Get codes specific to your unit.
C5Jumper cap malfunction protection-no jumper cap inserted, incorrect insertion, damaged…E1System high pressure protection-possible causes include excessive refrigerant, poor heat…E2Anti-freezing protection-evaporator freeze protection activated due to poor indoor air…E3System low pressure protection-low pressure switch has stopped operation.E4Compressor high discharge temperature protection.E5AC overcurrent protection-possible causes include unstable supply voltage, voltage too…E6Communication malfunction between indoor and outdoor units.E8High temperature resistant protection (overload/high temperature).EEEEPROM malfunction on outdoor control panel.EULimit/decrease compressor frequency due to high IPM module temperature.F1Indoor ambient temperature sensor open or short circuited.F2Indoor evaporator (tube) temperature sensor open or short circuited.F3Outdoor ambient temperature sensor open or short circuited.F4Outdoor condenser temperature sensor open or short circuited.F5Outdoor discharge temperature sensor open or short circuited.F6Limit/decrease compressor frequency due to overload condition.F8Decrease compressor frequency due to overcurrent-input supply voltage too low or system…F9Decrease compressor frequency due to high discharge temperature-overload, high ambient…FHLimit/decrease compressor frequency due to anti-freezing protection-poor indoor air…FoRefrigerant gathering/recovery mode-system forced to run in cooling mode for refrigerant…H0Decrease compressor frequency due to high temperature resistant during heating operation.H1Defrosting mode-normal state during heating operation where compressor runs and…H2Static dedusting protection.H3Compressor overload protection.H4System abnormal-overload protection when tube temperature is too high.H5IPM module protection.H6Indoor fan motor locked/blocked protection-DC motor feedback failure or motor stalling.H7Compressor desynchronizing (loss of synchronism) protection.HCPFC (Power Factor Correction) protection.L3Outdoor DC fan motor malfunction-motor failure or connector loosened causing compressor…L9Power protection-electronic components protected when high power detected.LCCompressor failure start-up (start-up failure).LPIndoor unit and outdoor unit do not match.P0Compressor minimum frequency test state.P1Compressor rated frequency test state.P2Compressor maximum frequency test state.P3Compressor intermediate frequency test state.P5Overcurrent protection of compressor phase current.P7Module temperature sensor circuit malfunction.P8Module high temperature protection-IPM module overheating.PHDC bus-bar voltage too high.PLDC bus-bar voltage too low.PUCapacitor charging malfunction on outdoor unit.U1Compressor phase current detection circuit malfunction.U3DC bus-bar voltage dips/sag-supply voltage unstable.U5Malfunction of complete unit current detection circuit on outdoor unit.U7Four-way valve abnormal-supply voltage too low, 4V terminal loosened or broken, or 4V…U8Zero-crossing inspection circuit malfunction of IDU fan motor-may be caused by instant…U9Outdoor unit zero-crossing detection malfunction / whole unit current testing malfunction.
Get the full diagnostic procedure for any code
Step-by-step tests, expected values, wiring diagram references, and verified part numbers.
Get Started $9.95 3-day pass$29/month for unlimited access to all brands and Max AI diagnostics.
More Electrolux error codes
Common questions
How do I find the error code on my Electrolux Air Conditioner?
Most Electrolux air conditioners show the code directly on the control panel display. If your model has no display, it can be read by entering diagnostic mode with the key sequence for your model. The full procedures include model-specific instructions for reading codes.
Are these codes specific to my model?
The codes here apply broadly to Electrolux air conditioners. Meanings and diagnostic steps can vary by model and production year, so enter your model number for model-specific information and procedures.
What do I do if my code is not listed?
Some codes are model-specific or only appear in diagnostic mode. Enter your model number to get codes specific to your unit, or contact us. We update the database continuously from manufacturer service documentation.
How much does it cost to access the full diagnostic procedures?
A 3-day pass is $9.95 one-time and gives full access to all brands, codes, and procedures. Monthly access is $29/month with unlimited access to everything including Max AI diagnostics.