mypros+
Error code reference

GE Cooktop Error Code 107

EEPROM failure (hidden to user, no visual alarm).

GE codesGE cooktop codes

EEPROM failure (hidden to user, no visual alarm).

First step from the service manual

Recycle power to the cooktop.

The complete diagnostic procedure includes additional test steps, resistance specifications, wiring diagram references, and component test points.

MyPros+ Max

Get the full diagnostic procedure for 107.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What 107 means on a GE cooktop

Error code 107 on a GE cooktop indicates an EEPROM (Electrically Erasable Programmable Read-Only Memory) failure within the control board. The EEPROM is a small non-volatile memory chip embedded on the main control board that stores critical operational data, including calibration settings, configuration parameters, and user preferences. When the control board's processor cannot successfully read from or write to this chip, it logs error code 107 internally. Notably, this fault is classified as hidden from the user, meaning no visual alarm or display message appears on the cooktop's interface during normal operation.

Because the error is silent, it typically surfaces only during a diagnostic scan or when a technician reads the fault log from the control board. The failure can stem from data corruption within the EEPROM chip itself, often caused by a power surge, voltage irregularity, or an improper shutdown during a write cycle. In some cases, a temporary glitch in the board's communication bus causes a false EEPROM fault that clears after a power cycle.

If recycling power does not resolve the fault, the EEPROM chip or the entire main control board likely requires replacement. Since the EEPROM is typically soldered directly onto the control board rather than socketed, individual chip replacement requires micro-soldering skills and equipment. Most technicians address this by replacing the complete control board assembly. Persistent EEPROM failures can gradually degrade cooktop performance, as the control system may revert to default values or lose stored calibration data.

Source: manufacturer service documentation.

Common causes of 107

  1. 01

    Temporary power glitch causing EEPROM communication error

    Wiring / connection

    A brief voltage fluctuation or an improper power shutdown during a write cycle can cause the control board's processor to lose communication with the EEPROM, triggering the fault code. Recycling power to the cooktop is the first step to clear this condition.

  2. 02

    Power surge or voltage spike

    Part replacement

    A sudden surge in line voltage can corrupt data stored in the EEPROM or damage the chip's internal structure. If the fault reappears after power cycling, a surge event is a likely contributor.

  3. 03

    EEPROM chip data corruption

    Part replacement

    Over time or after repeated power interruptions, the data stored in the EEPROM can become corrupted, causing the control board processor to report a memory failure. This condition does not resolve with a power cycle alone.

  4. 04

    Failed or degraded main control board

    Part replacement

    If the EEPROM chip itself or the surrounding circuitry on the control board has failed, the fault will persist regardless of power cycling. Replacement of the full control board assembly is typically required in this scenario.

  5. 05

    Loose or corroded control board connections

    Wiring / connection

    Poor electrical connections to the control board can interfere with stable power delivery to the EEPROM chip, causing intermittent read/write failures. Inspecting and reseating board connectors may help rule out this cause.

See the test procedure for each cause

Frequently asked questions about 107

What does 107 mean on a GE cooktop?
Error code 107 on a GE cooktop indicates an EEPROM failure on the main control board. The EEPROM is the memory chip that stores the cooktop's calibration and configuration data. This code is hidden from the user, so no alarm or display message will appear during normal use. It is typically discovered only during a technician's diagnostic scan of the control board.
Will resetting the cooktop clear error code 107?
Recycling power to the cooktop is the recommended first diagnostic step and can clear the fault if it was caused by a temporary communication glitch. To reset, disconnect the cooktop from power for at least one minute, then restore power and check if the fault returns. If the error code 107 persists after a power cycle, a hardware issue with the EEPROM chip or control board is likely.
Is it safe to use my GE cooktop when error code 107 is present?
Because error code 107 is a hidden fault with no visual alarm, the cooktop may continue to operate normally in many cases. However, an EEPROM failure can cause the control board to lose calibration data or revert to default settings, which may affect performance over time. It is advisable to have the fault diagnosed by a qualified technician to determine whether continued use is appropriate.
How much does it cost to fix error code 107 on a GE cooktop?
If the issue requires a main control board replacement, parts alone typically range from around $100 to $300 or more depending on the specific cooktop model, with additional labor costs if a technician performs the repair. If the fault clears with a simple power cycle, there is no parts cost involved. Getting a diagnostic visit from a certified technician is the best way to determine the actual repair scope and cost.
Can I replace the EEPROM chip myself to fix this error?
The EEPROM chip is typically soldered directly onto the main control board, so replacing only the chip requires micro-soldering skills and specialized equipment that most DIYers do not have access to. In practice, the standard repair approach is to replace the entire control board assembly rather than attempting chip-level repair. A homeowner comfortable with appliance repair can replace the full control board, but working with soldering equipment on circuit boards is best left to experienced technicians.

Related GE cooktop codes

All GE cooktop codes
View all 67 GE cooktop codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass