mypros+
Error code reference

Samsung Washer Error Code SF2

System error caused by micro controller operation failure.

Samsung codesSamsung washer codes

System error caused by micro controller operation failure.

First step from the service manual

Replace Assy PCB.

The complete diagnostic procedure includes additional test steps, resistance specifications, wiring diagram references, and component test points.

MyPros+ Max

Get the full diagnostic procedure for SF2.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What SF2 means on a Samsung washer

The SF2 error code on a Samsung washer indicates a system-level failure caused by microcontroller operation failure within the main PCB assembly. The microcontroller is the central processing unit that governs all washer functions, including cycle sequencing, motor control, water inlet timing, drain operation, and sensor communication. When the microcontroller fails to operate correctly, the washer cannot execute commands reliably and triggers the SF2 fault to prevent further operation.

This type of error is rooted in the main PCB (printed circuit board) assembly itself rather than a peripheral component like a sensor or motor. The microcontroller may fail due to corrupted firmware, internal component failure on the board, power surge damage, or moisture intrusion that degrades the board's circuitry over time. Because the fault originates within the controller's own processing logic, external resets or component replacements elsewhere in the machine will not resolve the underlying problem.

The primary diagnostic step is replacement of the PCB assembly. Since the microcontroller is integrated directly onto the main control board and is not a serviceable component on its own, the entire board must be replaced as a unit. Technicians should verify that the power supply to the board is within spec before condemning the PCB, to rule out voltage irregularities that may mimic or trigger microcontroller faults.

Source: manufacturer service documentation.

Common causes of SF2

  1. 01

    Main PCB microcontroller failure

    Part replacement

    The microcontroller chip on the main control board has failed internally, preventing the washer from processing any commands. This is the primary cause of SF2 and requires full PCB assembly replacement.

  2. 02

    Power surge damage to the control board

    Part replacement

    A voltage spike from the power supply or an electrical storm can damage the microcontroller or surrounding circuitry on the PCB. Inspect the board for visible burn marks or component damage as a visual confirmation.

  3. 03

    Moisture or corrosion on the PCB

    Part replacement

    Water intrusion into the control board housing can cause corrosion on board traces or component leads, leading to erratic microcontroller behavior and triggering SF2. Check the board and its connector housing for signs of moisture damage.

  4. 04

    Corrupted or failed firmware on the microcontroller

    Part replacement

    The firmware that governs microcontroller operation can become corrupted, causing persistent operation failures. This condition cannot be corrected by a simple reset and typically requires board replacement.

  5. 05

    Unstable or incorrect supply voltage to the PCB

    Wiring / connection

    If the voltage reaching the main PCB is outside acceptable limits, the microcontroller may fail to operate correctly and produce an SF2 fault. Confirm incoming power meets specifications before replacing the board.

See the test procedure for each cause

Frequently asked questions about SF2

What does SF2 mean on a Samsung washer?
SF2 on a Samsung washer indicates a system error caused by microcontroller operation failure on the main PCB assembly. The microcontroller is the processing unit that controls all washer functions, and when it fails, the machine cannot operate safely. This fault points directly to the main control board and requires board replacement to resolve.
Can I fix SF2 on my Samsung washer myself?
The repair involves replacing the main PCB assembly, which is a task that some experienced DIYers can perform if they are comfortable working with appliance electronics and disconnecting wiring harnesses. However, because the fault is internal to the control board's microcontroller, there are no adjustments or simple fixes that will resolve it short of replacement. If you are not comfortable working with electronics, a professional technician is recommended.
Will resetting my Samsung washer clear the SF2 error?
A simple reset, such as unplugging the washer and plugging it back in, is unlikely to permanently clear the SF2 error. Because the fault originates from a microcontroller operation failure within the PCB itself, the underlying hardware problem will persist and the code will return. A full PCB assembly replacement is the corrective action.
Is it safe to use my Samsung washer when SF2 is displayed?
You should not attempt to continue using the washer while SF2 is active. A microcontroller failure means the washer cannot reliably control its functions, including water fill, spin, and drain operations. Continued use could result in improper cycle behavior or potential water damage.
How much does it cost to repair a Samsung washer SF2 error?
The cost to repair an SF2 error depends primarily on the price of the replacement main PCB assembly and labor if a technician is hired. Parts costs for Samsung washer control boards typically range from around $100 to $300 or more depending on the model, with professional labor adding an additional $75 to $200. Getting a quote from a repair technician before committing is advisable, as the total cost should be weighed against the age and value of the machine.

Related Samsung washer codes

All Samsung washer codes
View all 232 Samsung washer codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass