mypros+
Model reference

Samsung WA50F9A6DSW/A2-00

Washer

2 documents21 error codes15 service modes

Available documentation

Service Manual

  • WASHING MACHINE (TOP-LOADING) SERVICE Manual35 pg
    Covers this model

Tech Sheet

  • Fast Track Troubleshooting9 pg
    Covers this model
MyPros+ Max

Diagnose your Samsung WA50F9A6DSW/A2-00.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (21)

CodeMeaning
1EWater level sensor error3EMCU is attempting to drive the motor but is not getting any response signals…4EWater fill error4E2Hot/cold water hose connection is not correct.5EDrainage failure8EMEMS sensor output is over 4.5V or under 0.5V and it continues for more than 10…8E1MEMS sensor output is over 4.5V or under 0.5V and it continues for more than 10…8E2MEMS sensor output is over 4.5V or under 0.5V and it continues for more than 10…AECommunication error between Sub PCB and Main PCB.bE2A button (except the Power button) is continually pressed.dEDoor is detected as open while it is trying to lock the door.dE1Door fails to unlock after 5 attempts.EEEEThe PCB assembly is defective.LEWater level over the reset water level is detected 4 seconds during the…OEOverflow fault detected in the water level sensor; data/frequency shows the…PEClutch motor errorPE1Clutch motor error.SdSuds detected during the washing sessionSudSuds detected during the washing sessiontEWater temperature sensor fault is detected continuously for 10 seconds.UEUnbalance of cabinet detected during final spin.

Service modes (15)

  • Circulation/Drain Pump Test (within Quick Test Mode)In Quick Test Mode, press Spin to test Circulation/Drain Pump.
  • Cycle Count (within Service Mode)While in Service Mode, press Pre Soak to see how many times the unit was used.
  • Door Lock Switch Status (Peripheral Input Test within Quick Test Mode)In Quick Test Mode, select Eco Plus, then turn the Jog-Dial so that the Quick Wash LED is turned on
  • Door Lock/Unlock Circuit Test (within Quick Test Mode)In Quick Test Mode, press My Cycle to test Door Lock/Unlock circuit.
  • Door Status Display (Peripheral Input Test within Quick Test Mode)In Quick Test Mode, select Eco Plus, then turn the Jog-Dial so that the Delicates/Hand Wash LED is…
  • Fault Code Test (within Service Mode)While in Service Mode, press Spin to view stored fault codes, then turn Jog Dial to view error codes
  • Motor Test (within Quick Test Mode)When either Test or Spin is displayed on the LCD, press Start/Pause to conduct the motor test
  • Quick Spin Test (within Service Mode)While in Service Mode, press and hold Delay Start & Softener Option
  • Quick Test ModeWith the power OFF, press Spin, Soil, & Power simultaneously.
  • Service ModeWith the power ON, press Delay Start & Pre Soak simultaneously.
  • Software Version (within Service Mode)While in Service Mode, press Soil Level to see the SW version information.
  • Water Level Frequency Display (Peripheral Input Test within Quick Test Mode)In Quick Test Mode, select Eco Plus, then turn the Jog-Dial so that the Pure Cycle LED is turned on
  • Water Temperature Display (Peripheral Input Test within Quick Test Mode)In Quick Test Mode, select Eco Plus, then turn the Jog-Dial so that the Perm Press LED is turned…
  • Water Valves Circuit Test (within Quick Test Mode)In Quick Test Mode, turn the Jog-Dial CCW so that the version disappears, then press Temp to cycle…
  • Water/Steam Heater Test (within Quick Test Mode)In Quick Test Mode, press Soil to test the Water/Steam Heater.

Full entry steps, exit procedures, and test sequences are available in Max.

Related Samsung washer models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass