mypros+
Error code reference

Thermador Range Error Code d:10

WFMC motor control

Thermador codesThermador range codes

WFMC motor control: Power limiter switch off (motor overloaded or binding).

MyPros+ Max

Get the full diagnostic procedure for d:10.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What d:10 means on a Thermador range

The d:10 error code on a Thermador range indicates that the WFMC (Washing Fan Motor Control) power limiter switch has shut off due to a detected motor overload or binding condition. This is a protective shutdown triggered by the motor control board when the motor driving a fan or convection component draws excessive current or encounters mechanical resistance beyond its rated operating parameters. The power limiter switch functions as an electronic overcurrent protection mechanism, cutting power to prevent thermal damage or motor burnout.

The WFMC motor control monitors current draw continuously during operation. When the motor becomes mechanically bound, such as by a seized bearing, a foreign object obstructing the fan blade, or accumulated grease buildup on rotating components, the motor draws significantly more current than normal to overcome the resistance. The control interprets this elevated current draw as an overload condition and activates the power limiter shutoff to protect the motor and associated wiring.

Binding can also result from a failing motor whose internal bearings are degrading, causing increasing mechanical drag over time. In some cases, the fault lies not with the motor itself but with the motor control board, which may be misreading current levels due to a faulty current sensing circuit. Diagnosing this code requires distinguishing between a true mechanical obstruction or motor failure and an electronics-side fault on the control board.

Source: manufacturer service documentation.

Common causes of d:10

  1. 01

    Fan blade obstruction or binding

    Wiring / connection

    A foreign object, grease buildup, or debris lodged against the fan blade can prevent it from spinning freely, causing the motor to overload. Inspect the fan blade for any physical blockage or resistance when turned by hand.

  2. 02

    Seized or failing motor bearings

    Part replacement

    Internal bearing wear in the fan motor causes increasing mechanical drag, eventually triggering the power limiter. A motor with bad bearings may make grinding or squealing noises before the fault appears.

  3. 03

    Motor winding failure

    Part replacement

    A short or partial failure within the motor windings causes abnormally high current draw even without a mechanical obstruction. This requires testing the motor's resistance values and comparing against specifications.

  4. 04

    Faulty WFMC motor control board

    Part replacement

    A defective current sensing circuit on the motor control board may incorrectly detect an overload condition even when the motor is functioning normally. This is typically diagnosed after the motor and mechanical components have been ruled out.

  5. 05

    Wiring harness fault between motor and control board

    Wiring / connection

    Damaged, corroded, or loose wiring between the motor and the control board can cause erratic current readings that trigger the power limiter shutoff. Inspect connectors and wiring insulation for visible damage.

See the test procedure for each cause

Frequently asked questions about d:10

What does d:10 mean on a Thermador range?
The d:10 code means the WFMC motor control has activated its power limiter switch due to a detected motor overload or binding condition. The control has shut the motor off to protect it from damage caused by excessive current draw. This typically points to a fan that is mechanically obstructed, a failing motor, or in some cases a fault on the motor control board itself.
Can I fix the d:10 error on my Thermador range myself?
Some causes of d:10 can be addressed without professional help, such as clearing a physical obstruction from the fan blade or cleaning away heavy grease buildup that is impeding rotation. However, if the motor bearings are seized, the motor windings have failed, or the control board is faulty, those repairs require component replacement and a comfort level with appliance disassembly. If you are unsure, a qualified technician should inspect the unit.
Is it safe to keep using my Thermador range when the d:10 code is active?
No, continued operation is not recommended when d:10 is active. The power limiter has shut off the motor specifically to prevent overheating and potential damage to the motor and surrounding components. Running the range while this fault is present could worsen the underlying problem and may pose a risk if the motor is severely bound or overheating.
Will resetting the Thermador range clear the d:10 error code?
A power reset may temporarily clear the d:10 code, but if the underlying cause such as a binding fan, failing motor, or control board fault has not been resolved, the code will return when the motor is operated again. Resetting without diagnosing the root cause is not a lasting solution and delays necessary repairs.
How much does it cost to repair a Thermador range showing the d:10 error?
Repair costs vary depending on the root cause. Clearing a physical obstruction may cost little to nothing beyond labor. Replacing a fan motor typically runs in the range of $150 to $400 including parts and labor. A motor control board replacement can cost more, often in the $250 to $600 range depending on parts availability and service rates in your area.

Related Thermador range codes

All Thermador range codes
View all 180 Thermador range codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass