mypros+
Error code reference

Thermador Range Error Code F44

Lower motorized latch will not unlock.

Avg. service call
$285
National average. Trip fee plus diagnostic plus labor. Before parts.
MyPros+ 3-day pass
$9.95
Same diagnostic steps, on your phone. Start now.
You keep in your pocket
~$275
Even before you buy the part.
Skip the service call. Fix it yourself.
Full procedure unlocks instantly.
Get Started

What the F44 error code actually means

Your Thermador oven's door latch is stuck in the locked position and the oven cannot automatically unlock it. This usually happens after a self-clean cycle when the locking mechanism does not release as expected. Until this is fixed, the oven door may remain locked and the oven should not be used.

Diagnostic procedure

The full F44 procedure

Step 1 is visible so you can confirm you are on the right page. The remaining steps, the ones that tell you whether to actually replace a part, unlock with any pass.

MyPros+ · DiagnosticsStep 1 preview
1
First diagnostic step
Check P24 connector on Power Board; ensure door latch switches operating properly; check wires not pinched; check P10 connector; if persists replace Power Board.
More steps, wiring diagram references, and verified part numbers
Includes expected resistance and voltage values, connector pinouts, and supersession notes for replacement parts.
Unlock F44 procedure $9.95

Or subscribe: $29/month for unlimited access to all codes plus Max AI diagnostics.

Most common causes of F44

Ranked by how often they cause this code
  1. 1Loose or faulty P24 connector on the Power Board
  2. 2Pinched or damaged latch wiring
  3. 3Failed door latch switches
  4. 4Loose or faulty P10 connector on the Power Board
  5. 5Defective Power Board

Most DIYers save hundreds by diagnosing before ordering parts.

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass

Questions people ask about F44

What does F44 mean on a Thermador range?
F44 means the lower motorized door latch is not unlocking as commanded by the control system. This typically surfaces after a self-clean cycle when the latch should release once the oven has cooled. The fault points to a problem in the latch motor circuit, latch switches, associated wiring, or the Power Board that controls the latch.
Is it safe to use my Thermador range when F44 is displayed?
You should avoid using the oven while the F44 error is active. A malfunctioning door latch can leave the oven door unexpectedly locked or interfere with normal self-clean safety functions. Operating the oven in this condition could create a situation where the door cannot be opened if needed, so the issue should be resolved before resuming use.
How much does it cost to repair a Thermador range F44 error?
Repair costs vary depending on the cause. If the fix is a reseated connector or a repositioned pinched wire, the cost may be limited to a service call fee, typically in the range of $80 to $150. If the door latch switches need replacement, parts and labor could bring the total to $150 to $300. A Power Board replacement is the most expensive scenario, with total repair costs potentially ranging from $300 to $600 or more depending on parts availability and labor rates in your area.
Can I fix F44 on my Thermador range myself?
Some steps in the diagnostic process, such as checking connectors P24 and P10 for secure seating and inspecting wires for pinching, are accessible to a knowledgeable DIYer comfortable working around oven electronics. However, testing door latch switches for proper operation and replacing the Power Board if needed generally require experience with appliance electrical systems and appropriate safety precautions. If you are not confident working around oven wiring, a qualified technician is recommended.
Will resetting the range clear the F44 error code?
A power reset by unplugging the range or cycling the circuit breaker may temporarily clear the code, but the error will return if the underlying latch problem is not resolved. The root cause, whether a loose connector, damaged wire, faulty switch, or failed Power Board, must be identified and corrected for the fault to clear permanently.

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass