Model reference

Amana YY-100-AH

Name: Amana YY-100-AH
Brand: Amana

Furnace

5 documents12 error codes17 service modes

Available documentation

Tech Sheet

Tech Sheet24 pg
Covers this model

Tech Tip

Control Guide38 pg
Covers this model

Installation Guide

Installation Instructions8 pg
Covers this model
Instrucciones de instalacion18 pg
Covers this model
Instrucciones de instalacion18 pg
Covers this model

MyPros+ Max

Diagnose your Amana YY-100-AH.

Step-by-step diagnostics from the service manual
Test values, resistance specs, and wiring references
Verified part numbers when replacement is needed

Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

M+

M+ Max·Amana Furnace

E1 on my Amana YY-100-AH

M+

Oven temperature sensor shorted —

From Tech Sheet W17706376, p.28:

1.Access service mode to confirm the active fault code and read stored error history.

2.Disconnect the sensor and measure resistance. Expected: 10 kΩ to 12 kΩ at 77°F (25°C).

3.Check the sensor harness for opens. A reading outside 5 kΩ to 50 kΩ indicates a failed sensor.

Part WP8577274

Temperature thermistor

Error codes (12)

CodeMeaning

E1Oven temperature sensor shorted E2Oven temperature sensor open F1E4Exhaust air template detector failure.F2E1Stuck key failure.F4E1Cavity temperature sensor failure.F4E4Humidity sensor error.F4E9AccuPop error.F8E5Loss of communication between Wi-Fi module and control.FCE1Microwave ACU failure.FCE2Appliance not linked to the wireless router.FCE3Appliance not linked to the internet.FCE7Appliance failed to connect to the wireless router.

Service modes (17)

Adjustable Audible SignalPress and hold STOP TIME for 5 seconds.
Child LockoutPress and hold START for 5 seconds.
Clock DisablePress and hold CLOCK for 5 seconds.
Demo FeaturePress and hold TIMER SET for 5 seconds.
Diagnostic / Test Mode["Plug in microwave oven or reconnect power.","Press CANCEL button to enter Standby mode (display…
Diagnostic/Test Mode["Plug in microwave oven or reconnect power and press the Cancel keypad to standby (':').","Close…
Diagnostics / Test Mode1. Plug in microwave oven or reconnect power and press Cancel button to Standby (':'). 2. Close…
Diagnostics Mode["Plug in microwave oven or reconnect power.","Press CANCEL button to reach standby display…
Diagnostics Mode - Key Functions["Enter Diagnostics Mode (CANCEL
Diagnostics Mode (Self-Diagnostic Test Mode)["Plug in microwave oven or reconnect power.","Press CANCEL button to enter standby (display shows…
Diagnostics Mode / Self-Diagnostic Test Mode["Plug in microwave oven or reconnect power.","Press CANCEL to go to standby (':' on…
Fahrenheit/Celsius ConversionPress and hold CUSTOM BROIL for 5 seconds.
Failure Code Verification["Enter the Diagnostics mode (press CANCEL
Service Diagnostics Mode["Press the pulsing JennAir logo to wake up the UI.","Press the middle zone key.","Press Connect…
Showroom Mode["Press and hold top and bottom zone icons simultaneously for 3 seconds."]
Temperature Adjustment (Calibration)Press and hold BAKE for 4 seconds, then press TEMP UP or DOWN arrow, then press START.
Touch Panel and ACU PCBA Test (Diagnostics Mode)["Plug in microwave oven or reconnect power and press Cancel button to Standby (':').","Close door…

Full entry steps, exit procedures, and test sequences are available in Max.

Related Amana furnace models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass