mypros+
Model reference

GE WBVH6240F0WW

Washer

3 documents33 error codes15 service modes

Available documentation

Service Manual

  • GE Front Load Washer Technical Service Guide61 pg
    Covers this model
  • GE Front Load Washer Technical Service Guide61 pg
    Covers this model

Job Aid

  • Procedure for Programming the GE Front Load Washer Control1 pg
    Covers this model
MyPros+ Max

Diagnose your GE WBVH6240F0WW.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (33)

CodeMeaning
E22Fill timeoutE23Flood protect drainE30Drain pump not presentE31Drain timeoutE38Dispenser errorE39Dispenser timeoutE42Drive motor instantaneous excess current draw.E43DC FaultE45Drive motor overload currentE46Drive motor over temperatureE47Heat sink over temperatureE48Drive motor openE49Drive motor overload powerE4AUnder voltsE4BOver voltsE4COver voltsE4EUnder volts after startE4FEEProm faultE52Main control wake-up errorE53Buffer errorE54No motor responseE57Checksum failureE58Communication failureE60Door lock switch failureE61Door unlock switch failureE62System contact failureE63Unexpected open doorE64Unexpected open door while runningE65Water level sensor failure (foam)E66Water temperature sensor open.
View all 33 error codes
E67Water temperature sensor shorted.E70Stuck keyE71Key fault

Service modes (15)

  • Control Board Programming Mode1. Reconnect power to the washer (display will show '---' meaning no model selected). 2. Rotate the…
  • Service Test Mode["Press Power button to clear any current cycles (display must be blank).","Disconnect the power…
  • t01 - Model ID["Enter Service Test Mode.","Rotate cycle knob to t01.","Press Start/Pause to display model ID…
  • t02 - Error Codes["Enter Service Test Mode.","Rotate cycle knob to t02.","Press Start/Pause to display most recent…
  • t03 - Software ID["Enter Service Test Mode.","Rotate cycle knob to t03.","Press Start/Pause to display software…
  • t04 - LED Illumination and Button Test["Enter Service Test Mode.","Rotate cycle knob to t04.","Press Start/Pause to test LEDs and cycle…
  • t05 - Pump Test["Enter Service Test Mode.","Rotate cycle knob to t05.","Press Start/Pause
  • t06 - Pressure Switch Test["Enter Service Test Mode.","Rotate cycle knob to t06.","Press Start/Pause
  • t07 - Thermistor/Heater Test["Enter Service Test Mode.","Rotate cycle knob to t07.","Press Start/Pause
  • t08 - Hot Water Test["Enter Service Test Mode.","Rotate cycle knob to t08.","Press Start/Pause
  • t09 - Cold Water Test["Enter Service Test Mode.","Rotate cycle knob to t09.","Press Start/Pause
  • t10 - Tumble Test["Enter Service Test Mode.","Rotate cycle knob to t10.","Press Start/Pause
  • t11 - Spin Test (Low/High)["Enter Service Test Mode.","Rotate cycle knob to t11.","Press Start/Pause
  • t12 - Dispenser Test["Enter Service Test Mode.","Rotate cycle knob to t12.","Press Start/Pause to advance through each…
  • t14 - Spin Speed Ramp Up Test["Enter Service Test Mode.","Rotate cycle knob to t14.","Press Start/Pause

Full entry steps, exit procedures, and test sequences are available in Max.

Related GE washer models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass