mypros+
Model reference

KitchenAid KDTE254EWH0

Dishwasher

9 documents59 error codes8 service modes

Available documentation

Tech Sheet

  • Tech Sheet W10750900 Rev C12 pg
    Covers this model
  • Tech Sheet12 pg
    Covers this model

Service Manual

  • Dimension Guide2 pg
    Covers this model
  • Kenmore Elite 2013 Stainless Steel Tall Tub Dishwashers82 pg
    Covers this model

Service Flash

  • KITCHENAID UNDER-COUNTER DISHWASHER - Intermittent Operation of the Capacitive Touch Control Panel Buttons3 pg
    Covers this model
  • Technical Service Pointer - W10841713 (Door Clicking)6 pg
    Covers this model

Tech Tip

  • Instruction Sheet2 pg
    Covers this model

Other

  • technicalreferencemanual 2211031382 pg
    Covers this model

Installation Guide

  • Installation Instructions76 pg
    Covers this model
MyPros+ Max

Diagnose your KitchenAid KDTE254EWH0.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (59)

CodeMeaning
1-1Control detected K400 pilot relay stuck on.1-2Damaged or corrupted memory / software issue on control board.10-1Dispenser electrical problem10-2Vent wax motor electrical problem (not all models)10-3Drying fan error (on models with fan)2-1Control detected stuck key(s) in keypad or keypad connection.2-2User Interface cannot communicate with main control (no response from UI).3-1Thermistor/OWI open3-2Thermistor/OWI shorted3-3Thermistor/OWI failed calibration.4-1Wash motor failure4-4Wash motor failure; loose connection in wash motor circuit and/or open wash…5-1Door switch stuck open5-2Door switch stuck closed6-1Inlet water low/no water (mechanical problem)6-2Fill valve electrical problem6-3Suds/air in pump6-4Float switch open6-6Cool water; incoming water temperature under 18°C/65°F.6-7Disconnected or damaged flowmeter.6-8Water softener regen valve electrical problem (water softener models only)7-1No heat7-2Heater stuck on8-1Slow drain8-3Drain motor not running (implied from context of draining errors).8-4Drain motor electrical problem9-1Diverter can't find position9-2Diverter stuck on9-3Control detected diverter disk in sump is missing.9-4Lower spray arm error
View all 59 error codes
F10E1Detergent dispenser electrical problemF10E2Vent motor linear electrical problem (model dependent)F10E3Drying fan errorF1E1Power relay K400 detected stuck in closed position.F1E2Damaged or deteriorated memory on control module board, or incompatible…F2E1User interface key stuck/blocked detected by control module.F2E2User interface cannot communicate with main control module; incorrect…F3E1Thermistor/soil sensor circuit openF3E2Thermistor/soil sensor circuit shortF3E3Soil sensor (OWI) calibration impossibleF4E4Wash motor inoperativeF5E1Door switch stuck in open positionF5E2Door switch stuck in closed positionF6E1No water or insufficient water level (mechanical problem)F6E2Fill valve electrical problemF6E3Excessive sudsing/air in pump.F6E4Float switch openF6E7Disconnected or damaged flowmeter.F6E8Water softener regeneration solenoid electrical problemF7E1No heat/water heating problemF7E2Heater element stuck in active modeF7E7Flow meter disconnected or damaged.F8E1Slow drainF8E3Drain motor electrical problem (variable speed)F8E4Drain motor problemF9E1Diverter valve cannot find its positionF9E2Diverter valve stuck openF9E3Diverter valve disc missing from tub bottom.F9E4Lower spray arm error

Service modes (8)

  • Clear Customer Error History["Enter Service Diagnostics Cycle.","During the first interval, press HI TEMP key to clear customer…
  • Customer Program Fast Advance Mode["Start a customer program.","Press HI TEMP
  • Rapid Advance (Customer Cycle)["Start a customer cycle.","Press HIGH TEMP
  • Rapid Advance Mode (during active cycle)After starting a cycle, press HI TEMP
  • Sales Demo Mode ClearRun Service Diagnostics Cycle to clear demo mode.
  • Service Diagnostic CycleWith dishwasher in standby, press any 3 keys in the sequence 1-2-3, 1-2-3, 1-2-3 with no more than…
  • Service Diagnostic Program["Press START/RESUME to activate the control panel from standby mode.","Press any 3 keys in…
  • Service Diagnostics Cycle["Press START/RESUME to wake up control panel.","Press any 3 keys in the sequence 1-2-3-1-2-3-1-2-3…

Full entry steps, exit procedures, and test sequences are available in Max.

Related KitchenAid dishwasher models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass