Model reference

KitchenAid KUDE48FXBL0

Dishwasher

19 documents59 error codes8 service modes

Available documentation

Service Manual

2013 Stainless Steel Tall Tub Dishwasher120 pg
Covers this model

Tech Sheet

TechSheet W10455258 RevA FR2 pg
Covers this model
Tech Sheet - W10195614 - Rev E (FR)2 pg
Covers this model
Jennair Dishwasher JDB8500AWX3 W10455257 Tech Sheet2 pg
Covers this model

Service Flash

Technical Service Pointer - Electronically Controlled Dishwashers with Thermal Cut-Off (TCO)3 pg
Covers this model
ProDry™ (with Fan Assist Operation) vs. non Fan Assist Models9 pg
Covers this model
Technical Service Pointer - W10475713 - Rev A (Vent Removed)3 pg
Covers this model
Service Pointer - W10460581 (Moisture Detected Inside Door Panels)2 pg
Covers this model
Single Pvc Toe/kick Panel and Plastic Retention Clips4 pg
Covers this model

Tech Tip

Instruction Sheet2 pg
Covers this model
Installation Instructions6 pg
Covers this model

Other

W10195613 - Rev D_W101956132 pg
Covers this model
instructionsheet w10497070 RevC 56 pg
Covers this model
Service Pointer - W10460578 - Rev B (Latch Blocks Door From Closing)_W104605789 pg
Covers this model
W10460578B9 pg
Covers this model

Installation Guide

Instruction Sheet2 pg
Covers this model
Installation Instructions Undercounter Dishwasher56 pg
Covers this model
Instruction Sheet1 pg
Covers this model
Instruction Sheet for Heater Element kit2 pg
Covers this model

MyPros+ Max

Diagnose your KitchenAid KUDE48FXBL0.

Step-by-step diagnostics from the service manual
Test values, resistance specs, and wiring references
Verified part numbers when replacement is needed

Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

M+

M+ Max·KitchenAid Dishwasher

1-1 on my KitchenAid KUDE48FXBL0

M+

Control detected K2 pilot relay stuck

From Tech Sheet W18168723, p.15:

1.Access service mode to confirm the active fault code and read stored error history.

2.Measure control board supply voltage at test points. Expected: 12 VDC and 5 VDC.

3.Inspect all connectors on the main control for corrosion or backed-out pins.

Part WPW10804018

Electronic control board

Error codes (59)

CodeMeaning

1-1Control detected K2 pilot relay stuck closed.1-2Damaged or corrupted memory on control board or incompatible software…10-1Dispenser electrical problem 10-2Vent wax motor electrical problem 10-3Drying fan error 2-1Control detected stuck key(s) in keypad or keypad connection.2-2No response from User Interface 3-1Open connector or component in Temperature Sensing Circuit, or open/faulty…3-2Shorted connection or component in Temperature Sensing Circuit, shorted or…3-3OWI failed calibration.4-1No communication between control and wash motor.4-2Motor communication error between control and wash motor.4-4Wash motor failure 5-1Door stuck open 5-2Door stuck closed 6-1Low/no water 6-2Fill valve electrical problem 6-3Suds/air in pump 6-4Float switch open 6-6Cool water 6-7Flowmeter problem 6-8Regen valve electrical problem 7-1No heat 7-2Heater stuck on 8-1Slow drain 8-2Drain pump impeller fractured.8-3Drain motor electrical problem 8-3 (stuck on)Drain stuck on 8-4Drain motor electrical problem 9-1Diverter can't find position

View all 59 error codes

9-2Diverter stuck on 9-3Diverter disk missing 9-4Diverter problem (general).F10E1Dispenser electrical problem F10E2Vent wax motor electrical problem F10E3Drying fan error F1E1Control detected K400 pilot relay stuck closed.F1E2Damaged or corrupted memory on control board; incompatible software components…F2E1Control detected stuck key(s) in keypad or keypad connection.F2E2User interface cannot communicate with main control; loose user interface…F3E1Open connection or component in temperature sensing circuit; open or faulty…F3E2Shorted connection or component in temperature sensing circuit; incoming water…F3E3OWI (Optical Water Indicator) failed calibration.F4E4Wash motor failure due to loose connection in wash motor circuit and/or open…F5E1Door was not latched within 3 seconds of pressing Start/Resume, or loose…F5E2Control programmed to not start if it suspects the door switch is stuck closed…F6E1Low or no water to dishwasher (mechanical problem)F6E2Fill valve electrical problem F6E3Suds or air detected in pump F6E4Float switch stuck in overfill (open) position and/or dishwasher not level…F6E6Incoming water temperature under 18°C/65°F (cool water detected).F7E1No heat F7E2Heater stuck on F8E1Slow drain F8E4Drain motor electrical problem F9E1Diverter can't find position F9E2Diverter stuck on F9E3Diverter disc missing F9E4Lower spray arm error

Service modes (8)

Clear Customer Error HistoryDuring Service Diagnostic Cycle Interval 4, press HI TEMP key to clear customer error history.
Clear Error HistoryDuring Service Diagnostics Cycle interval with Hi Temp LED on (10 seconds pause after Error 4)…
Error Code ReadingRun Service Diagnostics Cycle
Rapid Advance Mode["After starting a cycle, press HI TEMP
Rapid Advance Mode (during normal cycle)Press HI TEMP
Service Diagnostic CycleWith dishwasher in standby mode, press any 3 keys in the sequence 1-2-3, 1-2-3, 1-2-3 with no more…
Service Diagnostics CycleWhile in standby, press any 3 keys in the sequence 1-2-3-1-2-3-1-2-3 with no more than 1 second…
Service Diagnostics Rapid AdvanceDuring the Service Diagnostics Cycle, press Start/Resume key to advance 1 interval at a time.

Full entry steps, exit procedures, and test sequences are available in Max.

Related KitchenAid dishwasher models

78,000+ service manuals · 160,000+ error codes · 55+ brands

$29/month · Cancel anytime · Or $9.95 3-day pass