mypros+
Model reference

Whirlpool KGRS308BSS1

Range

11 documents36 error codes22 service modes

Available documentation

Tech Sheet

  • Tech Sheet - W10538800 - Rev A (FR)8 pg
    Covers this model
  • W10538799 - Rev A8 pg
    Covers this model

Service Manual

  • Troubleshooting Gas and Electric Freestanding Range Electronic Controls70 pg
    Covers this model

Service Flash

  • Service Pointer - W10701463 (Clock Display Frozen)3 pg
    Covers this model
  • Whirlpool Range Service Pointer W10702913A Revised6 pg
    Covers this model
  • Service Pointer - W10702913 - Rev A (Bake Burner May Not Ignite)6 pg
    Covers this model

Tech Tip

  • Instruction Sheet4 pg
    Covers this model

Installation Guide

  • Installation Instructions40 pg
    Covers this model
  • Instruction Sheet2 pg
    Covers this model

Quick Reference

  • Quick Reference Manual2 pg
    Covers this model
  • Oven Cleaning Quick Reference Guide2 pg
    Covers this model
MyPros+ Max

Diagnose your Whirlpool KGRS308BSS1.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (36)

CodeMeaning
F1Control failure or UL A/D error(s) detected in the control board.F1 E*Control board failure (all F1 sub-codes indicate control fault).F1-E0EEPROM communication error.F1-E5Sensor out of range.F1-E7Board thermistor open or short-circuited.F1-E9WIDE queue full.F1E0EEPROM communication error.F1E5Sensor out of range.F1E7PCB thermistor open or shorted.F1E9WIDE queue full.F2Shorted/stuck key detected on the control keypad.F2-E0Keypad disconnected.F2-E1Stuck key.F2-E2Cancel key error.F2E0Keypad disconnected.F2E1Stuck key.F2E2Cancel key error.F3Oven sensor opened or oven sensor shorted.F3 E0Oven temperature sensor fault (open or shorted)F3 E1Lower oven temperature sensor fault (MRC II double oven models).F3 E2Warming drawer temperature sensor fault.F3-E0Main oven sensor open or short-circuited.F3-E2Warm drawer sensor open or short-circuited (on some models).F3E0Main oven sensor open or shorted.F3E2Warming drawer sensor open or shorted (on some models).F5 E0Door position switch faultF5 E1Door latch switch/system faultF5 E2Door switch fault.F5-E0Door and door switch mismatch.F5E0Door and door switch do not agree.
View all 36 error codes
F6 E*Control communication failure.F6-E1Bake excessive temperature.F6-E3Warm drawer excessive temperature.F6E1Over temperature during cook.F6E3Over temperature in warming drawer.F9House miswired

Service modes (22)

  • Auto TestAfter entering diagnostic mode (CANCEL>CANCEL>START), press up arrow, '+', or '3' to scroll to AUTO…
  • Diagnostic/Troubleshooting Mode (MRC2)Press CANCEL > CANCEL > START
  • Diagnostics Mode (MRC2 Control)Press CANCEL > CANCEL > START
  • DISPLAYEnter diagnostic mode, scroll to mode 5 (DISPLAY).
  • ENG MODEEnter Diagnostics Mode, scroll to service mode 2 (ENG MODE)
  • ENG MODE (Engineering Mode)Enter diagnostic mode, scroll to mode 2 (ENG MODE)
  • FAULTSEnter diagnostic mode, scroll to mode 7 (FAULTS).
  • LCC Diagnostic Mode (LCC90/LCC95/LCC180)["Press CANCEL, CANCEL, START in sequence.","Press TEMP/TIME '+' key to cycle through diagnostic…
  • LCC190 Diagnostic Mode (Self Clean, Convection models)["Press CANCEL, CANCEL, START in sequence.","Press TEMP/TIME or TEMP/HOUR '+' key to cycle through…
  • MRC Diagnostic Mode["Press CANCEL, CANCEL, START in sequence.","Press TEMP/TIME '+' key to cycle through diagnostic…
  • MRC Diagnostic Mode (Fan/True Convection Electric - Oven Light entry)["Press CANCEL, CANCEL, START in sequence.","Press TEMP/TIME '+' key to cycle through diagnostic…
  • MRC II Diagnostic Mode (Number 3 key entry - KitchenAid models)["Press OFF/OFF/START or CANCEL/CANCEL/START in sequence.","Press the number '3' key to cycle…
  • MRC II Diagnostic Mode (TEMP/TIME entry)["Press CANCEL, CANCEL, START in sequence.","Press TEMP/TIME '+' keypad to cycle through diagnostic…
  • RELAY USAGEEnter diagnostic mode, scroll to mode 8 (RELAY USAGE).
  • Temperature Adjustment (MRC2 Controls)1
  • Temperature Calibration AdjustmentPress and hold OVEN LIGHT for 5 seconds
  • TEST MODEEnter Diagnostics Mode, scroll to service mode 3 (TEST MODE)
  • TEST MODE (Relay Control)Enter diagnostic mode, scroll to mode 3 (TEST MODE).
  • TEST ON (Relay Checks)Enter Diagnostics Mode (CANCEL > CANCEL > START)
  • TEST ON (Relay Control)Enter diagnostic mode (CANCEL>CANCEL>START)
  • USAGEEnter diagnostic mode, scroll to mode 1 (USAGE) using up arrow/'+'/3.
  • VERSIONEnter diagnostic mode, scroll to mode 4 (VERSION).

Full entry steps, exit procedures, and test sequences are available in Max.

Related Whirlpool range models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass