Model reference

Whirlpool SF462LXSQ1

Range

11 documents41 error codes3 service modes

Available documentation

Tech Sheet

Tech Sheet - W10116296A6 pg
Covers this model
Whirlpool Range SF362LXSB0 Tech Sheet6 pg
Covers this model
Whirlpool Range SF362LXST0 Tech Sheet6 pg
Covers this model

Service Manual

Whirlpool Gas Range Direct Spark Ignition System29 pg
Covers this model
Job Aid - 30″ Freestanding Self-Cleaning Gas Range68 pg
Covers this model
30″ Freestanding Self-Cleaning Gas Range68 pg
Covers this model
Whirlpool Gas Range Direct Spark Ignition System KR-2829 pg
Covers this model

Service Flash

Service Pointer - 8178185 - Rev A Ignition Problems2 pg
Covers this model
Service Pointer - 8178446 - PF Error Code Appears All the Time2 pg
Covers this model

Installation Guide

Installation Instructions16 pg
Covers this model
Instruction Sheet2 pg
Covers this model

MyPros+ Max

Diagnose your Whirlpool SF462LXSQ1.

Step-by-step diagnostics from the service manual
Test values, resistance specs, and wiring references
Verified part numbers when replacement is needed

Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

M+

M+ Max·Whirlpool Range

E0-F1 on my Whirlpool SF462LXSQ1

M+

EEPROM checksum failure.

From Tech Sheet W11637353, p.45:

1.Access service mode to confirm the active fault code and read stored error history.

2.Measure control board supply voltage at test points. Expected: 12 VDC and 5 VDC.

3.Inspect all connectors on the main control for corrosion or backed-out pins.

Part WPW10804018

Electronic control board

Error codes (41)

CodeMeaning

E0-F1EEPROM checksum failure.E0-F3Oven sensor opened.E0-F5Door and switches do not agree.E1-F1UL A/D error(s).E1-F3Oven sensor shorted.E1-F5Door latch not operating.E2-F2Shorted key detected.E2-F3BAKE/BROIL range over temperature.E2-F5Latch error during CLEAN.E3-F3CLEAN range over temperature.F0 E0Factory default F1 E0EEPROM checksum failure.F1 E1EEPROM communications error.F1 E2UL A/D error(s).F1 E4Model ID error.F1 E6Latch signal mismatch error.F1-E0EEPROM communications / EEPROM checksum failure.F1-E1EEPROM checksum failure.F1-E2UL A/D error(s).F2 E0Shorted key detected.F2 E1Key tail unplugged.F3 E0Oven sensor opened.F3 E1Oven sensor shorted.F3 E2BAKE/BROIL range over temperature.F3 E3CLEAN range over temperature.F3 E4Oven sensor opened F3 E5Oven sensor shorted F3 E6Warming drawer sensor open.F3 E7Warming drawer sensor shorted.F3-E0Oven sensor opened (open circuit in oven temperature sensor).

View all 41 error codes

F3-E1Oven sensor shorted.F3-E2BAKE/BROIL range over temperature condition.F3-E3CLEAN range over temperature condition.F5 E0Door and switches do not agree.F5 E1Door latch not operating.F5 E2Latch error during CLEAN.F5-E0Door and switches do not agree (door switch mismatch).F5-E1Door latch not operating.F5-E2Latch error during CLEAN cycle.F8 E0N/A (no likely failure condition described).PFA reset has occurred in the Electronic Range Control (ERC), typically caused by…

Service modes (3)

Diagnostics ModeWith oven not in cooking, broiling, or cleaning mode, press Cancel/OFF, Cancel/OFF, START. The…
Last Error Code RecallPress and hold the CANCEL/OFF key for 5 seconds until the last error code is displayed.
Temperature Adjustment ModePress and hold BAKE key for 5 seconds

Full entry steps, exit procedures, and test sequences are available in Max.

Related Whirlpool range models

78,000+ service manuals · 160,000+ error codes · 55+ brands

$29/month · Cancel anytime · Or $9.95 3-day pass