Model reference

Whirlpool WGE755C0BE00

Range

4 documents36 error codes12 service modes

Available documentation

Tech Sheet

Fiche technique - Tech Sheet - W10600809 - Rev A (FR)24 pg
Covers this model
Tech Sheet - W10600805 - Rev A16 pg
Covers this model

Installation Guide

Installation Instructions20 pg
Covers this model
Instruction Sheet1 pg
Covers this model

MyPros+ Max

Diagnose your Whirlpool WGE755C0BE00.

Step-by-step diagnostics from the service manual
Test values, resistance specs, and wiring references
Verified part numbers when replacement is needed

Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

M+

M+ Max·Whirlpool Range

F1-E0 on my Whirlpool WGE755C0BE00

M+

EEPROM communication error (internal).

From Tech Sheet W16385601, p.13:

1.Access service mode to confirm the active fault code and read stored error history.

2.Measure control board supply voltage at test points. Expected: 12 VDC and 5 VDC.

3.Inspect all connectors on the main control for corrosion or backed-out pins.

Part WPW10804018

Electronic control board

Error codes (36)

CodeMeaning

F1-E0EEPROM communication error (internal).F1-E1Upper RTD uncalibrated (internal).F1-E2Lower RTD uncalibrated (internal).F1-E5Sensor usage out of range (internal).F1-E7PCB thermistor/sensor open or shorted.F1-E9WIDE Queue full.F1E0EEPROM communication error (internal control fault).F1E1Upper RTD sensor not calibrated (internal control fault).F1E2Lower RTD sensor not calibrated (internal control fault).F1E5Sensor usage out of range (internal control fault).F1E7PCB sensor/thermistor open or short-circuited.F1E9WIDE queue full.F2-E0Keypad disconnected.F2-E1Stuck key detected.F2-E2Stuck key detected.F2E0Keypad disconnected from oven control module.F2E1Stuck key detected on keypad.F2E2Stuck key detected on keypad.F3-E0Main oven temperature sensor open or shorted (upper oven).F3-E1Main oven temperature sensor open or shorted (lower oven).F3E0Upper (main) oven temperature sensor open or short-circuited.F3E1Lower (main) oven temperature sensor open or short-circuited.F5-E0Door and door position switch(es) do not agree during Clean mode.F5-E1Door latch not operating during Clean mode.F5E0Door switch and door position switch mismatch during clean mode.F5E1Door latch does not operate properly during clean mode.F6-E0Lost communications between control components.F6-E1Over temperature condition during cook mode (runaway temperature).F6-E2Over temperature condition during clean mode (runaway temperature).F6-E3Over temperature condition in warming drawer (runaway temperature).

View all 36 error codes

F6E0Loss of communications between control modules.F6E1Bake mode runaway temperature (oven temperature exceeded safe limit during…F6E2Clean mode runaway temperature (oven temperature exceeded safe limit during…F6E3Warming drawer runaway temperature (exceeded safe limit).F9-E0Product is mis-wired.F9E0Product is miswired (incorrect wiring detected).

Service modes (12)

Control Reset (Soft Reset)1
Diagnostic ModePress CANCEL > CANCEL > START
Diagnostics ModePress CANCEL > CANCEL > START
Display Test1
Faults (View/Clear Error Codes)1
Semi Automatic Test Mode1
Semi-Automatic Test1. Enter diagnostic mode (CANCEL > CANCEL > START). 2. Press TEMP/TIME '+' or '-' (or keys 3 or 6…
Temperature Calibration1
Test Mode1
Test Mode (Manual Relay Activation)1
Usage Mode1
Version1

Full entry steps, exit procedures, and test sequences are available in Max.

Related Whirlpool range models

78,000+ service manuals · 160,000+ error codes · 55+ brands

$29/month · Cancel anytime · Or $9.95 3-day pass