Model reference
Whirlpool YWFE361LVQ0
Range
8 documents25 error codes11 service modes
Available documentation
Tech Sheet
- Fiche technique - Tech Sheet W103844608 pg
- Tech Sheet - W10384454 - Rev A8 pg
Service Manual
- Troubleshooting Gas and Electric Freestanding Range Electronic Controls70 pg
Service Flash
- Technical Service Pointer - W10412840 (Passive Door Hinge Design)6 pg
- Technical Service Pointer - W10473748 (F9 E0 Error Code)6 pg
Tech Tip
- Instruction Sheet4 pg
Installation Guide
- Installation Instructions16 pg
- Instruction Sheet2 pg
MyPros+ Max
Diagnose your Whirlpool YWFE361LVQ0.
- Step-by-step diagnostics from the service manual
- Test values, resistance specs, and wiring references
- Verified part numbers when replacement is needed
Start diagnosing
$29/month · Cancel anytime · Or $9.95 3-day pass
Error codes (25)
CodeMeaning
F1Internal board failure (control board malfunction).F1 E*Control board failure (all F1 sub-codes indicate control fault).F1E0Internal board failure.F1E1Internal board failure.F1E2Internal board failure.F2A/D error(s)F2E0Shorted key detected on control.F3Oven sensor opened, oven sensor shorted, bake/broil range over temperature, or…F3 E0Oven temperature sensor fault (open or shorted)F3 E1Lower oven temperature sensor fault (MRC II double oven models).F3 E2Warming drawer temperature sensor fault.F3E0Oven sensor opened.F3E1Oven sensor shorted.F3E2Bake/broil range over temperature condition.F3E3Clean range over temperature condition.F5Door and switches do not agree during clean mode.F5 E0Door position switch faultF5 E1Door latch switch/system faultF5 E2Door switch fault.F5E0Door and switches do not agree during clean mode.F5E1Door latch not operating during clean mode.F5E2Door and switches do not agree during clean mode.F6 E*Control communication failure.F9Miswired house or miswired range.F9E0Miswired house or miswired range.Service modes (11)
- diagnosticPress CANCEL > CANCEL > START within 5 seconds.
- diagnostic_test_modeFrom within diagnostic mode, press the following buttons to test individual relays: BAKE (toggles…
- Diagnostics ModePress CANCEL > CANCEL > START within a 5-second period.
- Diagnostics Test Mode (Relay Checks)While in Diagnostics Mode, press individual keypads to test control relays
- LCC Diagnostic Mode (LCC90/LCC95/LCC180)["Press CANCEL, CANCEL, START in sequence.","Press TEMP/TIME '+' key to cycle through diagnostic…
- LCC190 Diagnostic Mode (Self Clean, Convection models)["Press CANCEL, CANCEL, START in sequence.","Press TEMP/TIME or TEMP/HOUR '+' key to cycle through…
- MRC Diagnostic Mode["Press CANCEL, CANCEL, START in sequence.","Press TEMP/TIME '+' key to cycle through diagnostic…
- MRC Diagnostic Mode (Fan/True Convection Electric - Oven Light entry)["Press CANCEL, CANCEL, START in sequence.","Press TEMP/TIME '+' key to cycle through diagnostic…
- MRC II Diagnostic Mode (Number 3 key entry - KitchenAid models)["Press OFF/OFF/START or CANCEL/CANCEL/START in sequence.","Press the number '3' key to cycle…
- MRC II Diagnostic Mode (TEMP/TIME entry)["Press CANCEL, CANCEL, START in sequence.","Press TEMP/TIME '+' keypad to cycle through diagnostic…
- Temperature Adjustment ModeStep 1
Full entry steps, exit procedures, and test sequences are available in Max.
Related Whirlpool range models
78,000+ service manuals · 160,000+ error codes · 55+ brands
Get Started$29/month · Cancel anytime · Or $9.95 3-day pass